National Instruments GPIB Series Скачать руководство пользователя | Manualshive

Страница: 17 / 62

background image

©

National Instruments Corporation

2-1

GPIB-ENET/100 for Windows Me/98/95

2

Installation

This chapter describes how to install NI-488.2 for Windows Me/98/95 and
the GPIB-ENET/100.

Note

If you have a GPIB-ENET instead of a GPIB-ENET/100, refer to

Getting Started

with Your GPIB-ENET and NI-488.2 for Windows Me/98/95

for installation instructions.

Installing NI-488.2

Before you install the GPIB-ENET/100 hardware, complete the following
steps to install the NI-488.2 software:

1.

Insert the

NI-488.2 for Windows

CD.

2.

When the NI-488.2 Software for Windows screen appears, click the

Install NI-488.2 Software for Windows

item, as shown in Figure 2-1.

Figure 2-1.

NI-488.2 Software for Windows CD Autorun Screen

«
...
15
16
17
18
19
...
»

Содержание GPIB Series































































Отзывы:

Нет отзывов

Похожие инструкции для GPIB Series

Бренд: Accom Страницы: 15

Бренд: MC Страницы: 21

Бренд: Advantech Страницы: 68

Бренд: Xtreme Страницы: 83

Бренд: Vacron Страницы: 16

Бренд: SilverStone Страницы: 28

Бренд: Xcellon Страницы: 24

Бренд: Aleratec Страницы: 16

Бренд: LevelOne Страницы: 4

Бренд: Abus Страницы: 98

Бренд: TEC Control Страницы: 4

cPCI-3520 Series

Бренд: ADLINK Technology Страницы: 81

9500S-8 - Escalade RAID Controller

Бренд: 3Ware Страницы: 46

SECURE BOOT STICK FX

Бренд: Ecos Страницы: 22

Бренд: Cambium Networks Страницы: 132

Бренд: Faroudja Страницы: 17

Бренд: Faroudja Страницы: 17

Бренд: Silicon Laboratories Страницы: 91

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды