National Instruments GPIB Series Скачать руководство пользователя | Manualshive

Страница: 14 / 62

background image

Chapter 1

Introduction

GPIB-ENET/100 for Windows Me/98/95

1-4

ni.com

The LEDs show the current status of the GPIB-ENET/100. Table 1-1
describes each LED.

NI-488.2 Overview

NI-488.2 includes a native, 32-bit multitasking Windows Me/98/95 driver
that is fully Plug and Play aware.

The NI-488.2 software supports the concurrent use of multiple types of
GPIB hardware. For example, you can communicate with GPIB devices
through an AT-GPIB/TNT, a PCMCIA-GPIB, and a GPIB-ENET/100 in
the same system at the same time. The NI-488.2 software is fully integrated
into the operating system.

Table 1-1.

LED Descriptions

LED

Description

PWR/RDY

Flashes rapidly at start-up while performing self
tests and when acquiring network parameters.
A steady yellow state indicates the box is ready for
operation. Slow flashing pattern indicates an error
occurred.

LINK
10/100

Indicates the GPIB-ENET/100 detected a twisted
pair (10Base-T or 100Base-TX) link. The color
indicates the connection speed. If yellow, the speed
is 10 Mbits/s. If green, the speed is 100 Mbits/s.

TX

Indicates the GPIB-ENET/100 is transmitting to
the Ethernet network.

RX

Indicates the GPIB-ENET/100 is receiving
Ethernet network traffic.

TALK

Indicates the GPIB-ENET/100 is configured as a
GPIB Talker.

LISTEN

Indicates the GPIB-ENET/100 is configured as a
GPIB Listener.

«
...
12
13
14
15
16
...
»

Содержание GPIB Series































































Отзывы:

Нет отзывов

Похожие инструкции для GPIB Series

Бренд: Qlogic Страницы: 8

Бренд: ZALMAN Страницы: 5

RouterBOARD 411R

Бренд: 4gon Страницы: 2

ZyXEL ZyAIR B-120

Бренд: ZyXEL Communications Страницы: 20

Бренд: Disc Makers Страницы: 38

Бренд: Freescale Semiconductor Страницы: 8

NVRx-7300 series

Бренд: Swann Страницы: 9

Бренд: Alphacool Страницы: 9

BPN-SAS3-LB16A-N10

Бренд: Supermicro Страницы: 11

Бренд: WIN Enterprises Страницы: 25

VAR-SOM-MX6 HEAT PLATE KIT

Бренд: Variscite Страницы: 3

Бренд: Panduit Страницы: 5

Wireless LAN Board-B2

Бренд: Canon Страницы: 100

HORIZON Random Access Memory

Бренд: NorthStar Страницы: 69

Бренд: StarTech.com Страницы: 9

Бренд: Aardvark Страницы: 12

Бренд: Advantech B+B SmartWorx Страницы: 6

SuperMassive 9200

Бренд: SonicWALL Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды