background image

© 

National Instruments Corp.

9

FP-PWM-520 and cFP-PWM-520

[c]FP-PWM-520, it sends initial configuration information to the 
[c]FP-PWM-520. After the [c]FP-PWM-520 receives this initial 
information, the green 

READY

 indicator lights and the module is 

in normal operating mode.

In addition to the green 

POWER

 and 

READY

 indicators, each 

channel has a numbered, green status LED that lights when the 
channel is in the ON state.

Upgrading Your FieldPoint Firmware

You may need to upgrade your FieldPoint firmware when you add 
new I/O modules to your FieldPoint system. For information on 
determining which firmware you need and how to upgrade your 
firmware, go to 

ni.com/info

 and enter 

fpmatrix

.

Isolation and Safety Guidelines

Caution

Read the following information before 

attempting to connect the [c]FP-PWM-520 to any circuits 
that may contain hazardous voltages.

This section describes the isolation of the [c]FP-PWM-520 and its 
compliance with international safety standards. The field wiring 
connections are isolated from the backplane and the inter-module 
communication bus. The isolation barriers in the module provide 
250 V

rms

 Measurement Category II continuous isolation, verified 

by 2,300 V

rms

, 5 s dielectric withstand test. The [c]FP-PWM-520 

provides 

double insulation

 (compliant with IEC 61010-1) for 

working voltages of 250 V

rms

1

. Safety standards (such as those 

published by UL and IEC) require the use of double insulation 
between hazardous voltages and any human-accessible parts or 
circuits.

Never

 try to use any isolation product between human-accessible 

parts (such as DIN rails or monitoring stations) and circuits that 
can be at hazardous potentials under normal conditions, unless the 
product is specifically designed for such an application, as is the 
[c]FP-PWM-520.

1  

Working voltage

 is defined as the signal voltage plus the common-mode voltage. 

Common-mode voltage

 is the voltage of the module with respect to ground.

Содержание FIELDPOINT cFP-PWM-520




















Отзывы: