National Instruments FieldPoint cFP-DO-400 Скачать руководство пользователя страница 12

Страница: 12 / 15

FP-DO-400 and cFP-DO-400

ni.com

Safety

This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement,
control, and laboratory use:

•

IEC 61010-1, EN 61010-1

•

UL 3121-1, UL 61010C-1

•

CAN/CSA C22.2 No. 1010.1

For UL, hazardous location, and other safety certifications, refer to
the product label or to

ni.com

Electromagnetic Compatibility

CE, C-Tick, and FCC Part 15 (Class A) Compliant

Emissions.......................................... EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity........................................... EN 61326:1997

A2:2001,

Table 1

Note

For EMC compliance, you

must

operate this device

with shielded cabling.

CE Compliance

This product meets the essential requirements of applicable
European Directives, as amended for CE marking, as follows:

Low-Voltage Directive (safety)......... 73/23/EEC

Electromagnetic Compatibility
Directive (EMC) ............................... 89/336/EEC

Note

Refer to the Declaration of Conformity (DoC) for

this product for any additional regulatory compliance
information. To obtain the DoC for this product,
click

Declarations of Conformity Information

ni.com/hardref.nsf/

Содержание FieldPoint cFP-DO-400
















Результаты поиска

Содержание FieldPoint cFP-DO-400

Отзывы:

Бренды по названию

Популярные бренды

National Instruments FieldPoint cFP-DO-400, Руководство по эксплуатации

Результаты поиска

Содержание FieldPoint cFP-DO-400

Отзывы:

Бренды по названию

Популярные бренды