National Instruments FieldPoint cFP-AI-110 Скачать руководство пользователя страница 18

Страница: 18 / 21

National Instruments Corp.

FP-AI-110 and cFP-AI-110

Operating shock
(IEC 60068-2-27).............................. 50 g, 3 ms half sine,

18 shocks at 6 orientations;
30 g, 11 ms half sine,
18 shocks at 6 orientations

Safety

This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement,
control, and laboratory use:

•

IEC 61010-1, EN 61010-1

•

UL 61010-1

•

CAN/CSA-C22.2 No. 61010-1

For UL, hazardous location, and other safety certifications, refer to
the product label or visit

ni.com/certification

, search by

model number or product line, and click the appropriate link in the
Certification column.

Electromagnetic Compatibility

Emissions.......................................... EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity........................................... EN 61326:1997

A2:2001,

Table 1

CE, C-Tick, and FCC Part 15 (Class A) Compliant

Note

For EMC compliance, you

must

operate this device

with shielded cabling.

Содержание FieldPoint cFP-AI-110






















Результаты поиска

Содержание FieldPoint cFP-AI-110

Отзывы:

Бренды по названию

Популярные бренды

National Instruments FieldPoint cFP-AI-110, Руководство по эксплуатации

Результаты поиска

Содержание FieldPoint cFP-AI-110

Отзывы:

Бренды по названию

Популярные бренды