National Instruments FieldPoint cFP-20 Series Скачать руководство пользователя страница 18

Страница: 18 / 76

Chapter 2

Installing Compact FieldPoint Hardware and Software

cFP-20xx and cFP-BP-x User Manual

2-6

ni.com

Mounting the Backplane on a Panel

The cFP-BP-

backplane is shipped with a panel-mount kit. Complete

the following steps to mount the backplane on a panel:

Fasten the two plates of the panel-mount kit to the back of the
cFP-BP-

using a number 2 Phillips screwdriver and the

8-32

5/16 in. countersink screws shipped with the kit. These

screws have a nylon coating to prevent them from loosening. Refer
to Figures 2-3 and 2-4.

Caution

not

use screws longer than 5/16 in. to fasten the panel-mount plates to the

backplane.

Figure 2-3.

Fastening the Panel-Mount Plates to the cFP-BP-4 Backplane

Bolt or screw the panel-mount accessory to a panel using 8-32 or
M4 screws.

TIO

INS

TRU

Содержание FieldPoint cFP-20 Series













































































Результаты поиска

Содержание FieldPoint cFP-20 Series

Отзывы:

Бренды по названию

Популярные бренды

National Instruments FieldPoint cFP-20 Series, Руководство пользователя

Результаты поиска

Содержание FieldPoint cFP-20 Series

Отзывы:

Бренды по названию

Популярные бренды