National Instruments DAQCard-6715 Скачать руководство пользователя | Manualshive

Страница: 63 / 103

background image

Chapter 5

Counters

©

National Instruments Corporation

5-9

Analog Output Series User Manual

•

Ctr1InternalOutput drives the CTR 1 OUT pin to trigger or control
external devices.

•

Ctr1InternalOutput can drive other internal signals.

Refer to

Device Routing in MAX

in the

NI-DAQmx Help

or the

LabVIEW

Help

in version 8.0 for more information.

Counter 1 Up/Down Signal

You can externally input this signal on the P0.7 pin, but it is not available
as an output on the I/O connector. When you enable externally controlled
count direction, Counter 1 counts down when this pin is at a logic low
and counts up when it is at a logic high. If you do not enable externally
controlled count direction, the P0.7 pin is free for general use.

Frequency Output Signal

This signal is available only as an output on the FREQ OUT pin. The
frequency generator for your device outputs on the Frequency Output
signal. The frequency generator is a four-bit counter that can divide
its input clock by the numbers one through 16. The input clock of the
frequency generator is software-selectable from the internal 10 MHz and
100 kHz timebases. The output polarity is software-selectable. This output
is set to high-impedance at startup.

Master Timebase Signal

The Master Timebase (MasterTimebase) signal, or Onboard Clock, is the
timebase from which all other internally generated clocks and timebases
on the board are derived. It controls the timing for the analog output and
counter subsystems. It is available as on output on the I/O connector, but
you must use one or more counters to do so.

The maximum allowed frequency for the MasterTimebase is 20 MHz,
with a minimum pulse width of 23 ns high or low. There is no minimum
frequency limitation.

The two possible sources for the MasterTimebase signal are the internal
20MHzTimebase signal or an external signal through RTSI 7. Typically the
20MHzTimebase signal is used as the MasterTimebase unless you wish
to synchronize multiple devices, in which case, you should use RTSI 7.
Refer to Chapter 8,

Real-Time System Integration Bus (RTSI)

information on which signals are available through RTSI.

«
...
61
62
63
64
65
...
»

Содержание DAQCard-6715








































































































Отзывы:

Нет отзывов

Похожие инструкции для DAQCard-6715

Бренд: Parker Страницы: 344

Бренд: DBM Страницы: 50

WS-650 lite Series

Бренд: Laurell Страницы: 84

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: Patton electronics Страницы: 16

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 8

Бренд: IEI Technology Страницы: 136

Powereta iQP Series

Бренд: TDK Страницы: 2

LITTLE BOARD P5X

Бренд: Ampro Corporation Страницы: 121

Бренд: Planet Страницы: 20

ELITE LCD UPGRADE KIT

Бренд: Corsair Страницы: 11

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

mPCIE-ADIO16-8F Series

Бренд: Acces I/O products Страницы: 13

Бренд: M86 Security Страницы: 540

Бренд: ebm-papst Страницы: 13

Бренд: LinMot Страницы: 62

HYPER-BT-E38 1 Series

Бренд: IEI Technology Страницы: 95

i.MX 6SoloLite Linux

Бренд: Freescale Semiconductor Страницы: 199

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды