National Instruments Compact FieldPoint Mounting Accessories... Скачать руководство пользователя страница 13

© 

National Instruments Corporation

13

cFP-21xx Quick Start Guide

4. Install Connector Blocks on the Backplane

In order to connect I/O modules to input signals or to external loads, you need to 
install a cFP-CB-

x

 connector block or other connectivity accessory for each I/O 

module on the backplane. Use the connector socket to the right of each I/O module 
socket.

Caution

Do not insert or remove connector blocks or other connectivity 

accessories while power is applied to them.

1. Wire field devices as described 

in the I/O module and connector 
block operating instructions. 

Caution

Hazardous voltage 

wiring should be performed 
by qualified personnel and 
in accordance with local 
electrical standards.

2. Align the captive screws on the 

connector block with the holes 
on the backplane.

3. Press firmly to seat the connector block on the backplane.

4. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.) 

length, tighten the captive screws to 1.1 N · m (10 lb · in.) of torque. 

5. Repeat this procedure to install additional connector blocks on the backplane.

Содержание Compact FieldPoint Mounting Accessories...





























Отзывы: