National Instruments Compact FieldPoint cFP-21 Series Скачать руководство пользователя

Страница: 12 / 74

National Instruments Corporation

2-1

cFP-21xx and cFP-BP-x User Manual

Installing Compact FieldPoint
Hardware and Software

This chapter explains how to install the Compact FieldPoint hardware and
software.

What You Need to Get Started

To set up and use LabVIEW Real-Time with the cFP-21

, you need the

following:

❑

cFP-21

Compact FieldPoint controller

❑

cFP-BP-

backplane

❑

Mounting hardware (DIN rail, panel-mount, or rack-mount accessory)

❑

cFP I/O module(s)

❑

Wiring accessories such as cFP-CB-

connector block(s) or cables

❑

11–30 VDC power supply (20 W recommended)

❑

Ethernet cable

❑

1/8 in. flathead and number 2 Phillips screwdrivers

❑

NI-FieldPoint software version 4.1.1

❑

A host PC running Windows 2000/NT 4.0

/XP

❑

LabVIEW Real-Time software

Using FieldPoint software with Windows NT 4.0 requires Service Pack 6 or later.

Содержание Compact FieldPoint cFP-21 Series











































































Результаты поиска

Содержание Compact FieldPoint cFP-21 Series

Отзывы:

Похожие инструкции для Compact FieldPoint cFP-21 Series

Бренды по названию

Популярные бренды

National Instruments Compact FieldPoint cFP-21 Series, Руководство пользователя

Результаты поиска

Содержание Compact FieldPoint cFP-21 Series

Отзывы:

Похожие инструкции для Compact FieldPoint cFP-21 Series

Бренды по названию

Популярные бренды