National Instruments cDAQ-9133 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 145

background image

1-40

|

ni.com

Chapter 1

Getting Started with the cDAQ Controller

Caution

You

must

use the SD card slot cover to protect the SD card in hazardous

locations.

Caution

Do

not

insert or remove SD cards unless power has been switched off or

the area is known to be nonhazardous.

Note

NI recommends that you primarily log data to the SD card when logging data.

Note

Using SD cards that are not approved by NI might invalidate specifications

and result in unreliable performance.

SD Card LEDs

The cDAQ controller has two LEDs that indicate SD card drive mount status and activity. Refer
to Table 1-9 for descriptions of each of the LEDs.

SD Card Slot Cover

You must use the SD card slot cover to protect the SD card in hazardous locations. Do not
remove an SD card while either LED is flashing or lit because file corruption may result.

Caution

Do

not

insert or remove SD cards unless power has been switched off or

the area is known to be nonhazardous.

Caution

Removing the SD card while the IN USE LED is lit might result in

incomplete or lost data.

Table 1-9.

SD Card LED Indications

LED

LED Color

LED State

Description

SD ACT

Yellow

Off

There is no I/O activity on the SD card in
the slot.

Flashing

The cDAQ controller is performing I/O on
the SD card in the slot. Do

not

remove the

SD card while this LED is flashing.

SD IN USE

Green

Off

There is no SD card present in the slot or
the cDAQ controller has unmounted the
SD card from the operating system. It is
safe to remove the SD card from the slot.

Solid

The SD card in the slot is mounted in the
operating system. Do

not

remove the SD

card while this LED is lit.

«
...
48
49
50
51
52
...
»

Содержание cDAQ-9133


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для cDAQ-9133

Бренд: ABB Страницы: 2

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

Бренд: VADDIO Страницы: 2

Бренд: Jetline Страницы: 58

Бренд: Caen Страницы: 20

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: Samson Страницы: 48

Бренд: National Instruments Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды