National Instruments cDAQ-9133 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 145

background image

1-36

|

ni.com

Chapter 1

Getting Started with the cDAQ Controller

Ethernet Ports

The cDAQ controller has two tri-speed RJ-45 Ethernet ports, shown in Figure 1-1 or 1-2.

Refer to Figure 1-26 for Ethernet pin locations and signal descriptions. The Ethernet signal
names are listed as Fast Ethernet signal name, RX/TX +/-, and then Gigabit Ethernet signal
name, (RX/TX_

x

+/-).

Figure 1-26.

Ethernet Port Pin Locations: Fast Ethernet Signals (Gigabit Ethernet Signals)

Note

Both Ethernet ports perform automatic crossover configuration so you do not

need to use a crossover cable to connect to a host computer.

(NI cDAQ-9132/9133/9134/9135/9136/9137 for Windows)

Both Ethernet ports are enabled

and configured as DHCP, to “obtain an IP address automatically,” by default. The Ethernet ports
can be configured in the Windows Control Panel, under the Network and Internet category. Both
Ethernet ports provide Wake-on-LAN functionality. The Ethernet ports remain powered when
the controller is in sleep mode.

(NI cDAQ-9132/9133/9134/9135/9136/9137 for LabVIEW Real-Time)

Both Ethernet ports

are enabled and configured to “obtain an IP address automatically,” by default. The Ethernet
ports can be configured in MAX

TX+ (TX_A+)
TX– (TX_A–)
RX+ (RX_B+)
No Connect (TX_C+)
No Connect (TX_C–)
RX– (RX_B–)
No Connect (RX_D+)
No Connect (RX_D–)

1
2

3

4
5
6
7

8

«
...
44
45
46
47
48
...
»

Содержание cDAQ-9133


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для cDAQ-9133

Бренд: U-Prox Страницы: 31

Бренд: MADRIX Страницы: 36

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: ABB Страницы: 44

Бренд: Omega Страницы: 2

Бренд: Zmotion Страницы: 34

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: DAQ Страницы: 63

Бренд: Reer Страницы: 2

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Freedom Bridge FB3

Бренд: Identiv Страницы: 2

Бренд: LOGICDATA Страницы: 23

Бренд: FuzzDog Страницы: 9

Universal Family for Sony

Бренд: Jolly Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды