manualshive.com logo in svg

National Instruments AT-GPIB/TNT, Начало работы, Страница: 30 / 64

Поделиться
Скачать
National Instruments AT-GPIB/TNT Скачать руководство пользователя страница 30

Chapter 2

Installation and Configuration

©

 National Instruments Corporation

2-13

AT-GPIB/TNT for Windows 98/95

Figure 2-10 shows the jumper position for selecting no DMA channel.

Figure 2-10.  AT-GPIB/TNT DMA Jumper Setting for No DMA Channel

Setting the AT-GPIB/TNT Shield Ground 
Configuration

The AT-GPIB/TNT is set at the factory with the jumper in place to 
connect the logic ground of the AT-GPIB/TNT to its shield ground. 
This configuration minimizes EMI emissions.

Caution:

The AT-GPIB/TNT was tested for compliance with FCC standards with the 
shield ground connected to logic ground. Removing the jumper might 
cause EMI emissions to exceed any or all of the applicable standards.

If your application requires that logic ground be disconnected from 
shield ground, follow these steps:

1.

Refer to Figure 2-5 to locate the shield ground jumper W3 on the 
AT-GPIB/TNT.

2.

Remove the jumper and place it across only one of the jumper pins, 
as shown in Figure 2-11.

DRQ7

DACK7

DRQ6

DACK6

DRQ5

DACK5

15

14

12

11

10

IRQ

= Used to Select the IRQ Level

!

Содержание AT-GPIB/TNT

































































Отзывы:

Нет отзывов