manualshive.com logo in svg

National Instruments AT-GPIB/TNT, Начало работы, Страница: 25 / 64

Поделиться
Скачать
National Instruments AT-GPIB/TNT Скачать руководство пользователя страница 25

Chapter 2

Installation and Configuration

AT-GPIB/TNT for Windows 98/95

2-8

©

 National Instruments Corporation

Follow these steps to reconfigure the base I/O address of the 
AT-GPIB/TNT:

1.

Locate the base I/O address switch at SW1 on your AT-GPIB/TNT 
board. Refer to the parts locator diagram, Figure 2-5.

2.

Change the switch settings to configure the GPIB board to match 
the base I/O address of the Input/Output Range assigned by 
Windows.

Press down on the side marked OFF to select a binary value of 1 for 
the corresponding address bit. Press down on the ON side of the 
switch to select a binary value of 0. Refer to Figure 2-6 for an 
example of the switch settings and corresponding base I/O 
addresses. Table 2-2 shows the possible switch settings, the 
corresponding base I/O addresses, and the I/O address space used 
for each setting. The default settings are in bold italics.

Table 2-2.  Possible Base I/O Address Switch Settings for AT-GPIB/TNT

Switch Setting

Base I/O

Address (hex)

I/O Address

Space Used (hex)

A9

A8

A7

A6

A5

0

1

0

0

0

100

100 to 11F

0

1

0

0

1

120

120 to 13F

0

1

0

1

0

140

140 to 15F

0

1

0

1

1

160

160 to 17F

0

1

1

0

0

180

180 to 19F

0

1

1

0

1

1A0

1A0 to 1BF

0

1

1

1

0

1C0

1C0 to 1DF

0

1

1

1

1

1E0

1E0 to 1FF

1

0

0

0

0

200

200 to 21F

1

0

0

0

1

220

220 to 23F

1

0

0

1

0

240

240 to 25F

1

0

0

1

1

260

260 to 27F

Содержание AT-GPIB/TNT

































































Отзывы:

Нет отзывов