manualshive.com logo in svg

National Instruments 9205, Процедура калибровки

Поделиться
Скачать
National Instruments 9205 Скачать руководство пользователя страница 14

NI 9205/9206 Calibration Procedure

14

ni.com

Test Point

The 

Test Point

 is the voltage value that is input or output for verification 

purposes. This value is broken down into two columns—

Location

 and 

Value

. 

Location

 refers to where the test value fits within the test range. 

Value

 refers to the voltage value to be verified. 

Max 

refers to maximum 

value, 

Min

 refers to minimum value, and 

Mid

 refers to mid-scale.

2-Year Limits

The 

2-Year Limits

 column contains the 

Upper Limits

 and 

Lower Limits

 for 

the test point value. That is, when the device is within its 2-year calibration 
interval, the test point value should fall between these upper and lower limit 
values.

Table 4.  

NI 9205/9206 Analog Input Values

Range (V)

Test Point

2-Year Limits

Minimum

Maximum

Location

Value (V)

Lower Limit (V)

Upper Limit (V)

–10

10

Max

9.980000

9.976836

9.983164

–10

10

Mid

0.000000

–0.001407

0.001407

–10

10

Min

–9.980000

–9.983164

–9.976836

–5

5

Max

4.990000

4.988303

4.991697

–5

5

Mid

0.000000

–0.000718

0.000718

–5

5

Min

–4.990000

–4.991697

–4.988303

–1

1

Max

0.998000

0.997617

0.998383

–1

1

Mid

0.000000

–0.000168

0.000168

–1

1

Min

–0.998000

–0.998383

–0.997617

–0.200

0.200

Max

0.199600

0.199489

0.199711

–0.200

0.200

Mid

0.000000

–0.000056

0.000056

–0.200

0.200

Min

–0.199600

–0.199711

–0.199489

Содержание 9205
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды