background image

Page 18 

National Communications

DIP SWITCH SETTINGS

Four Micro Dip Switches are located on the underside of CRU2.  These
switches are used to set your recording requirements.

DIP SWITCH 1 is used to control recording of INCOMING CALLS

If Dip Switch 1  is ON        -

Auto  Record  All  Incoming  Calls

If Dip Switch 1 is OFF      -

DO  NOT  Auto  Record  Incoming  Calls

DIP SWITCH 2 is used to control recording of OUTGOING CALLS

If Dip Switch 2 is ON        -

Auto  Record  All  Outgoing  Calls

If Dip Switch 2 is OFF      -

DO NOT Auto Record Outgoing Calls

DIP SWITCH 3 is used to control Manual Call Recording (see below)

If Dip Switch 3 is ON       -

Prevent  DTMF Override

If Dip Switch 3 is OFF      -

Allow  DTMF  Override

DIP SWITCH 4 is used to control the Recording Tone (see below)

If Dip Switch 4 is ON        -

Disable  Recording  Tone

If Dip Switch 4 is OFF      -

Allow  Recording  Tone

MANUAL CALL RECORDING CONTROL

If Dip Switch 3 is set to the OFF Position, the CRU unit will allow you to START
and STOP Call Recording AT ANY TIME, direct from your telephone. YOU
CAN START RECORDING telephone calls on an as required basis by simply
pressing 3, from any telephone connected to the same line. YOU CAN STOP
RECORDING telephone calls on an as required basis by simply pressing 4,
from any telephone connected to the same line.  With OUTGOING CALLS
only, there is a 6 second delay  before the 3 or 4 command is executed. The
delay is required in order to prevent the possibility of this unit responding
whenever DTMF Tone Dial digits are dialled out for phone banking or other
similar requirements.

RECORDING TONE

A Recording Tone can be injected into your telephone line at  intervals of 15
seconds, whenever calls are being recorded.  To enable the injection of call
recording tones when recording calls, set Dip Switch 4 to the OFF position. To
disable the injection of call recording tones when recording calls, set Dip Switch
4 to the ON position.

Disabling the Recording Tones should only be done after full consideration of
the applicable State and Commonwealth legislation relating to the recording of
communications over  the Telecommunications network.

Содержание CRU2





















Отзывы: