Set Up
3
enter the empty bag.
7. Close the lower bag clamp and
shut the red plug filler cap
to the lower bag. You now
have a full vein system for
access. Elevate the blood bag.
Leaving the clamp to the
lower bag closed will allow
you to attain a flash in the
catheter as you insert the
needle into the vein. The
higher the supply bag of blood
is hung, the more pressure is
created in the system to flash.
8. Once the catheter is installed
and secured, open the lower
bag tubing clamp to allow
titration of the drip in the IV
set-up.
9. Phlebotomy can be
accomplished without
opening the lower tubing
clamp.
Replacing IV Skins and Veins
Tubing and Veins: To replace
tubing in Simulaids IV Arm or
Hand:
Steps:
1. Remove skin and loosen
tubing.
PO Box 1289 – 16 Simulaids Drive Saugerties NY 12477 USA Tel: 845-679-2475 or 800-431-4310 Fax: 845-679-8996
www.simulaids.com [email protected]
•
•
•
•
Page 3 of 4
IV TRAINING ARM AND HAND
Assembly & Operation Instructions
8. Once the catheter is installed and secured, open the
lower bag tubing clamp to allow titration of the drip in
the IV set-up.
9. Phlebotomy can be accomplished without opening the
lower tubing clamp.
Tubing and Veins: To replace tubing in Simulaids IV Arm or
Hand:
Steps: 1. Remove skin and loosen tubing.
Replacing IV Skins and Veins
2. Clip tubing, leaving about an inch (1") protruding
from each hole.
3. Insert one of the supplied connectors into the end of
each piece of tubing that is left protruding from the IV
unit.
4. Cut the new tubing to the correct length between
connectors.
5. Slip new tubing onto connectors.
6. Replace skin.
7. Palpate the veins to make sure they are positioned in
the channel on the arm or hand.
Skins: To replace skins on SIMULAIDS IV Arm or Hand:
Steps: 1. Remove the used skin from the Arm or Hand. Carefully
cutting it off is quickest.
2. Sprinkle talcum powder from enclosed packet in the
interior of new skin.
3. Holding so that water cannot enter the inside, dip the
skin into hot water (120°-180°F) for approximately 15-
30 sec. This will make it easier to slip on and fit to
inner Arm or Hand.
4. Shake out excess powder and slide the new skin over
the Arm or Hand, pulling it into place.
5. Palpate veins to make sure they are positioned in the
channel on the arm or hand. Adjust as needed.
6. Trim excess skin with scissors.
Item No. Description
140
IV Training Arm and Hand (1 Arm Unit/1 Hand Unit)
146
IV Training Arm
147R
New IV Training Hand Right
141R
New IV Hand Skin (Right)
141L
Original Hand Skin (Left)
142
IV Arm Skin
143
IV Arm and/or Hand Vein Set
144
IV Reservoir (1)
225
Powder to make one gallon blood
148
WV IV Pro (4 pack)
Item numbers for IV Arm and Hand components
are listed below:
(continued on next page)
7b.
7.
1.
4.
PO Box 1289 – 16 Simulaids Drive Saugerties NY 12477 USA Tel: 845-679-2475 or 800-431-4310 Fax: 845-679-8996
www.simulaids.com [email protected]
•
•
•
•
Page 3 of 4
IV TRAINING ARM AND HAND
Assembly & Operation Instructions
8. Once the catheter is installed and secured, open the
lower bag tubing clamp to allow titration of the drip in
the IV set-up.
9. Phlebotomy can be accomplished without opening the
lower tubing clamp.
Tubing and Veins: To replace tubing in Simulaids IV Arm or
Hand:
Steps: 1. Remove skin and loosen tubing.
Replacing IV Skins and Veins
2. Clip tubing, leaving about an inch (1") protruding
from each hole.
3. Insert one of the supplied connectors into the end of
each piece of tubing that is left protruding from the IV
unit.
4. Cut the new tubing to the correct length between
connectors.
5. Slip new tubing onto connectors.
6. Replace skin.
7. Palpate the veins to make sure they are positioned in
the channel on the arm or hand.
Skins: To replace skins on SIMULAIDS IV Arm or Hand:
Steps: 1. Remove the used skin from the Arm or Hand. Carefully
cutting it off is quickest.
2. Sprinkle talcum powder from enclosed packet in the
interior of new skin.
3. Holding so that water cannot enter the inside, dip the
skin into hot water (120°-180°F) for approximately 15-
30 sec. This will make it easier to slip on and fit to
inner Arm or Hand.
4. Shake out excess powder and slide the new skin over
the Arm or Hand, pulling it into place.
5. Palpate veins to make sure they are positioned in the
channel on the arm or hand. Adjust as needed.
6. Trim excess skin with scissors.
Item No. Description
140
IV Training Arm and Hand (1 Arm Unit/1 Hand Unit)
146
IV Training Arm
147R
New IV Training Hand Right
141R
New IV Hand Skin (Right)
141L
Original Hand Skin (Left)
142
IV Arm Skin
143
IV Arm and/or Hand Vein Set
144
IV Reservoir (1)
225
Powder to make one gallon blood
148
WV IV Pro (4 pack)
Item numbers for IV Arm and Hand components
are listed below:
(continued on next page)
7b.
7.
1.
4.
2. Clip tubing, leaving about an
inch (1”) protruding from each
hole.
3. Insert one of the supplied
connectors into the end of
each piece of tubing that is left
protruding from the IV unit.
4. Cut the new tubing to the
correct length between
connectors.
5. Slip new tubing onto
connectors.
6. Replace skin.
7. Palpate the veins to make sure
they are positioned in the
channel on the arm or hand.
Skins: To replace skins on Nasco
Healthcare IV Arm or Hand:
Steps:
1. Remove the used skin from the
Arm or Hand. Carefully
cutting it off is quickest.
2. Sprinkle talcum powder from
enclosed packet in the interior
of new skin.
3. Holding so that water cannot
enter the inside, dip the
skin into hot water (120 -180 F)
for approximately 15-30 sec
PO Box 1289 – 16 Simulaids Drive Saugerties NY 12477 USA Tel: 845-679-2475 or 800-431-4310 Fax: 845-679-8996
www.simulaids.com [email protected]
•
•
•
•
Page 3 of 4
IV TRAINING ARM AND HAND
Assembly & Operation Instructions
8. Once the catheter is installed and secured, open the
lower bag tubing clamp to allow titration of the drip in
the IV set-up.
9. Phlebotomy can be accomplished without opening the
lower tubing clamp.
Tubing and Veins: To replace tubing in Simulaids IV Arm or
Hand:
Steps: 1. Remove skin and loosen tubing.
Replacing IV Skins and Veins
2. Clip tubing, leaving about an inch (1") protruding
from each hole.
3. Insert one of the supplied connectors into the end of
each piece of tubing that is left protruding from the IV
unit.
4. Cut the new tubing to the correct length between
connectors.
5. Slip new tubing onto connectors.
6. Replace skin.
7. Palpate the veins to make sure they are positioned in
the channel on the arm or hand.
Skins: To replace skins on SIMULAIDS IV Arm or Hand:
Steps: 1. Remove the used skin from the Arm or Hand. Carefully
cutting it off is quickest.
2. Sprinkle talcum powder from enclosed packet in the
interior of new skin.
3. Holding so that water cannot enter the inside, dip the
skin into hot water (120°-180°F) for approximately 15-
30 sec. This will make it easier to slip on and fit to
inner Arm or Hand.
4. Shake out excess powder and slide the new skin over
the Arm or Hand, pulling it into place.
5. Palpate veins to make sure they are positioned in the
channel on the arm or hand. Adjust as needed.
6. Trim excess skin with scissors.
Item No. Description
140
IV Training Arm and Hand (1 Arm Unit/1 Hand Unit)
146
IV Training Arm
147R
New IV Training Hand Right
141R
New IV Hand Skin (Right)
141L
Original Hand Skin (Left)
142
IV Arm Skin
143
IV Arm and/or Hand Vein Set
144
IV Reservoir (1)
225
Powder to make one gallon blood
148
WV IV Pro (4 pack)
Item numbers for IV Arm and Hand components
are listed below:
(continued on next page)
7b.
7.
1.
4.
PO Box 1289 – 16 Simulaids Drive Saugerties NY 12477 USA Tel: 845-679-2475 or 800-431-4310 Fax: 845-679-8996
www.simulaids.com [email protected]
•
•
•
•
Page 3 of 4
IV TRAINING ARM AND HAND
Assembly & Operation Instructions
8. Once the catheter is installed and secured, open the
lower bag tubing clamp to allow titration of the drip in
the IV set-up.
9. Phlebotomy can be accomplished without opening the
lower tubing clamp.
Tubing and Veins: To replace tubing in Simulaids IV Arm or
Hand:
Steps: 1. Remove skin and loosen tubing.
Replacing IV Skins and Veins
2. Clip tubing, leaving about an inch (1") protruding
from each hole.
3. Insert one of the supplied connectors into the end of
each piece of tubing that is left protruding from the IV
unit.
4. Cut the new tubing to the correct length between
connectors.
5. Slip new tubing onto connectors.
6. Replace skin.
7. Palpate the veins to make sure they are positioned in
the channel on the arm or hand.
Skins: To replace skins on SIMULAIDS IV Arm or Hand:
Steps: 1. Remove the used skin from the Arm or Hand. Carefully
cutting it off is quickest.
2. Sprinkle talcum powder from enclosed packet in the
interior of new skin.
3. Holding so that water cannot enter the inside, dip the
skin into hot water (120°-180°F) for approximately 15-
30 sec. This will make it easier to slip on and fit to
inner Arm or Hand.
4. Shake out excess powder and slide the new skin over
the Arm or Hand, pulling it into place.
5. Palpate veins to make sure they are positioned in the
channel on the arm or hand. Adjust as needed.
6. Trim excess skin with scissors.
Item No. Description
140
IV Training Arm and Hand (1 Arm Unit/1 Hand Unit)
146
IV Training Arm
147R
New IV Training Hand Right
141R
New IV Hand Skin (Right)
141L
Original Hand Skin (Left)
142
IV Arm Skin
143
IV Arm and/or Hand Vein Set
144
IV Reservoir (1)
225
Powder to make one gallon blood
148
WV IV Pro (4 pack)
Item numbers for IV Arm and Hand components
are listed below:
(continued on next page)
7b.
7.
1.
4.
