English
15
Threading
- Set the machine in position and drill a hole for a thread.
- With the machine turned off, set the machine to first gear
and use the speed regulator (22) to set the lowest possible
speed.
- Fasten a tap and switch rotation to the right using the ro-
tation direction switch (21).
- Turn on the machine and use the lever (6) to guide the
tool into the pre-drilled hole until you achieve the desired
thread length.
- Turn off the machine and use the switch (21) to change
rotation direction to the left.
- Turn on the machine and let the tool fully screw out of the
thread, then elevate the tool even further using the lever
(6) to avoid damaging the start of the thread.
Attention! When working on a ladder, scaffold and
so on, the operator must be secured against fall‑
ing. A power failure may result in the machine
swaying and causing the operator to fall!
Maintenance and Service
Attention! Risk of injury by electric current. Un‑
plug the device from the power socket before mak‑
ing any adjustments (such as mounting or remov‑
ing hand grips, replacing drill bits, etc.)!
The air holes on the housing of the motor must not be
clogged or covered.
The following procedures must be carried out after ap-
proximately 200 hours of operation:
- Checking brush length. Brushes shorter than 5 mm must
be replaced with new ones.
- Changing lubricating grease in the gearbox and bearings.
Attention! With the principles of protection
against injury by electric current and the protec‑
tion rating of the device in mind, all maintenance
and service work that requires the removal of the ma‑
chine’s casing must be done only by an authorised service
centre!
You can find the current list of authorised service centres on
our website at
www.narex.cz
in the
“Service Points”
section.
Storage
If stored packaged, the device can be stored in a dry store-
house without heating if the temperature inside does not drop
below -5 °C.
If stored unpackaged, the device can only be stored in a dry
storehouse where the temperature does not drop below +5 °C
and where there aren’t any sudden changes in the tempera-
ture.
Recycling
Electrical tools, accessories and packaging should all be sub-
mitted for reuse to prevent environmental damage.
EU countries only:
Do not put electrical tools into household waste!
In accordance with European Directive 2002/96/EC on waste
electrical and electronic equipment and the directive’s en-
forcement in national laws, unusable electrical tools must be
collected for reuse/recycling/recovery to prevent environmen-
tal damage.
Warranty
Our devices come with a warranty for material or production
defects in accordance with the legal regulations of the given
country, for a period no shorter than 12 months. In EU coun-
tries, the warranty period is 24 months for exclusively private
use (proven by an invoice or bill of delivery).
Damage caused by natural wear and tear, overloading, im-
proper handling, damage caused by the user or by use contra-
ry to the operating manual, or damage known already at the
time of purchase is excluded from the warranty.
Complaints can be accepted only if the device is sent back to
the supplier or a NAREX authorised service centre in a non-dis-
assembled state. Store and keep the operating manual, safety
instructions, list of spare parts and proof of purchase. Other-
wise, the manufacturer’s current warranty terms always apply.
Note
Based on constant research and development, the manufac-
turer reserves the right to change the technical information
stated here.
Declaration of Conformity
The manufacturer declares that the machine meets all relevant
provisions of applicable European Community regulations.
Safety:
EN 60745-1; EN 60745-2-1
Directive 2006/42/EC
Electromagnetic compatibility:
EN 50366; EN 55014-1; EN 55014-2; EN 61000-3-2;
EN 61000-3-3
Directive 2014/30/EU
RoHS:
Directive 2011/65/EU
The technical documentation is stored at:
Narex s.r.o., Chelčického 1932, 470 01 Česká Lípa, Czech Re-
public
2018
Narex s.r.o.
Chelčického 1932
Maciej Stajkowski
470 01 Česká Lípa
Executive Director
01. 04. 2018
