Narex 65 404 830, Оригинальное руководство по эксплуатации

Страница: 17 / 44

English
17
Technical specification
Cordless hammer drill/driver:
Model ASP 14-2A ASP 18-2A
Voltage 14.4 V 18.0 V
Idle speed: 1st range 0–460 rpm 0–460 rpm
2nd range 0–1 600 rpm 0–1 600 rpm
Max. number of impacts:
1st range 0–6 900 ipm 0–6 900 ipm
2nd range 0–24 000 ipm 0–24 000 ipm
Max. torque 54 Nm 60 Nm
Chuck – scope of clamping 0.8–10 mm 1.5–13 mm
Wood screws - dia. max.: 7 mm 8 mm
Drilling - dia. max.: into metal 10 mm 13 mm
into wood 35 mm 40 mm
into masonry 10 mm 13 mm
Threaded spindle for chuck 1/2“-20 UNF 1/2“-20 UNF
Weight w/o accumulators 1.36 kg 1.48 kg
Charger:
Model AN-UNI C
Input voltage 110–240 V
Frequency 50–60 Hz
Power input 80–100 W
Output voltage 16.6–20.7 V
Charging current 4 A
Charge time ca 25–45 min*
Weight 0.7 kg
Class of protection II /
Accumulator:
Model AP 14 LE AP 14 LP AP 18 LE AP 18 LP
Voltage 14.4 V 14.4 V 18.0 V 18.0 V
Cell type Li-Ion Li-Ion Li-Ion Li-Ion
Capacity 1.5 Ah 3.0 Ah 1.5 Ah 3.0 Ah
Temperature of charging 0–45 °C 0–45 °C 0–45 °C 0–45 °C
Charge time ca 25 min ca 45 min ca 25 min ca 45 min
Monitor. of the temp.of charging thermistor thermistor thermistor thermistor
Weight 0.44 kg 0.68 kg 0.52 kg 0.78 kg
* Depending on model and capacity of the accumulator to be charged!
Description:
1 ...........Accumulator
2 ...........Accumulator clamp
3 ...........Switching–in push button with speed control
4 ...........Reversing switch
5 ...........Speed changing switch
6a .........Adjusting ring for torque setting
6b .........Adjusting ring for drilling/hammer-drilling
7 ...........Workplace LED lighting
8 ...........Chuck clamp sleeve
9 ...........Accumulator state indication panel
10a .......Indication switch
10b ......Accumulator state indicator
11 .........LED signal lights
12 .........Charger
13 .........Vent holes of the accumulator air cooling system
Zobrazené anebo popsané příslušenství nemusí patřit do objemu
dodávky.
Scope of use
The cordless hammer drill/drivers are specified for screwing and
drilling into metals, wood and plastics and for hammer-drilling
into masonry.
Double insulation
To ensure maximum safety of the user our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two-wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 55014.
Charging battery pack instructions
1. Make sure that circuit voltage is the same as than shown on
the charger specification plate. Connect the charger (12) to
power source. Red LED signal light should light up (11). This
indicates the charger is ready to being charging. If the red LID
light is not on, check connection to the power source. If the
power source is OK, transport the charger into the authorized
service workshop!
2. Position the accumulator/battery pack (1) into the charger as
far as the stop, see the Fig.