background image

16 

 
 

Changing the valves of the 2rd stage:  
 

Please follow the procedure below: 
 

• 

Uscrew the intake and pressure linesfrom the cylinder head. 

• 

Fix the head. 

• 

Unscrew the intake valve body with the special tool. In order to avoid damaging the special tool or 
the valve when using the tool, ensure that it is pushed properly and firmly into the valve bore so 
that it will not tilt when it is turner. 

• 

Clean  intake  and  pressure  valves  and  check  for  wear.  Valve  seats  and  plate  valves  must  not 
show any signs of wear or damage. Replace damaged parts. 

• 

Assembly is performed in the riverse sequence of removal.  

• 

Peen the cylinder head on the screw-in thread of the intake valve in three place with a small drift 
pin. 

• 

Check the pressure valve function and stoke by lifting the valve plate. 

• 

Check O-rings and replace them if damaged. 

• 

Fix the head at cylinder. 

• 

Reconnect the intake and pressure lines. 

 
 
 
 
 

Changing the valves of the 3th stage:  
 
 

Please follow the procedure below: 
 

• 

Uscrew the intake and pressure linesfrom the cylinder head.. 

• 

Fix the head 

• 

Unscrew the intake valve body with the special tool. In order to avoid 
damaging the special tool or the valve when using the tool, ensure that 
it is pushed properly and firmly into the valve bore so that it will not tilt 
when it is turned. 

• 

Clean intake and pressure valves and check for wear. Valve seats and 
plate  valves  must  not  show  any  signs  of  wear  or  damage.  Replace 
damaged parts. 

• 

Assembly is performed in the reverse sequence of removal. 

• 

Peen  the  cylinder  head  on  the  screw-in  thread  of  the  intake  valve  in 
three place with a small drift pin. 

• 

Check the pressure valve function and stoke by lifting the valve plate. 

• 

Check O-rings and replace them if damaged. 

• 

Fix the head at cylinder. 

• 

Reconnect the intake and pressure lines. 

INSTRUCTION MANUAL PACIFIC 210 

Содержание Pacific 210




























Отзывы: