background image

20

ONE-YEAR LIMITED WARRANTY

The appliance has been manufactured under the highest standards of quality and workmanship. We

warrant to the original consumer purchaser that all aspects of this product will be free of defects in

material and workmanship for one (1) year from the date of purchase. A replacement for any defective

part will be supplied free of charge for installation by the consumer. Defects or damage caused by the

use of other than genuine parts are not covered by this warranty. This warranty shall be effective from

the date of purchase as shown in the purchaser’s receipt. 

This warranty is valid for the original consumer purchaser only and excludes industrial, commercial or

business use of the product, product damage due to shipment or failure which results from alteration,

product abuse, or product misuse, whether performed by a contractor, service company, or consumer.

We will not be responsible for labor charges and/or damage incurred in installation, repair or replace-

ment, nor for incidental or consequential damage.

NAC Customer Care

214 Bayview Drive

Barrie, ON

Canada, L4N 4Y8

1-866-820-8686

[email protected]

This warranty may give you specific legal rights that vary by state or province.

Содержание PTH40PGM





















Отзывы: