background image

 

5

EN

www.napoleon.com

N415-0543 JUL 17.20

NOTE!

 Propane regulator hose not included.

Gas Hook-Up Instructions

WARNING!

 This grill is designed for non-combustible enclosures only, and must be installed and 

serviced by a qualified installer to local codes.

WARNING!

 Cabinet frame, cabinet, and counter top must be made from non-combustible material.

WARNING!

 As indicated on the rating plate, this gas grill is designed to operate with gas supply 

pressures of 11” WC for Propane and 7” WC for Natural Gas.  For installations where the gas supply 

pressure exceeds these requirements, a regulator must be installed upstream of the grill’s components.  

If the gas supply pressure is lower than these requirements, the unit will be under-fired and will not 

reach the maximum temperatures.  Ensure that the supply line size complies with local and/or national 

installation codes.

BUILT IN PROPANE GAS HOOK-UP

: The piping up to the gas grill is the responsibility of the installer and 

piping should be located as shown in the built-in instructions.  A flexible metal connector is included to 

simplify the installation of the unit.  Connect this flexible metal connector to the flare fitting on the end of 

the manifold.  Connect the other end of the connector to the gas piping.  Ensure that the connector does 

not pass through a wall, floor, ceiling or partition, and is protected from damage.  Do not use a hose to 

connect the unit except 

to connect the cylinder regulator to the piping system.  It must be connected with 

!

!

General Information

This Gas Barbecue is certified under Canadian and American National Standards, CSA 1.6-2018 and ANSI 

Z21.58-2018 respectively for Outdoor Gas Grills and should be installed to conform according to local 

codes. In absence of local codes, install to the current CAN B149.1 Natural Gas and Propane Installation 

Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States.  
If a rotisserie motor is used, it must be electrically grounded in accordance with local codes or, in absence 

of local codes, with the current CSA C22.1 Canadian Electrical Code in Canada or the National Electrical 

Code, ANSI/NFPA 70 in the United States.

WARNING

: This product can expose you to chemicals including lead and lead compounds, which are 

known to the State of California to cause cancer, and chemicals including di-n-butyl phthalate, which are 

known to the State of California to cause birth defects or other reproductive harm. For more information 

go to www.P65Warnings.ca.gov.

Propane Cylinder Specifications

WARNING!

 If these instructions are not followed exactly, a fire causing death or serious injury may 

occur.

WARNING!

 Do not store a spare propane cylinder on the shelf beneath the barbecue.

If the gas grill is being supplied with propane from a portable cylinder, a regulator specified by the manu

-

facturer must be used.  The regulator must supply a pressure of 11 inches water column (0.39 PSI) to the 

gas grill and have a QCC1 type fitting. Cylinders to be used with this unit must be supplied with a QCC1 

cylinder valve.  A QCC1 cylinder has a positive seating connection, which will not allow gas flow until a 

positive seal has been achieved.  It is also equipped with an excess flow device.  In order to attain full flow 

to the grill, the valves must be in the off position when the cylinder valve is turned on.  

A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a 

cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance 

with the specifications for LP-gas cylinders of the National Standard of Canada, CAN/CSA-b339, Cylinders, 

Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable or the Speci

-

fications for LP-Gas Cylinders of the U.S. Department of Transportation (D.O.T.). Cart models have been 

designed for use with a 20 lb (9.1 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a cylinder connection device compatible with the connection 

for outdoor cooking appliances.  The propane cylinder must be provided with a shut-off valve terminat

-

ing in a propane cylinder valve type QCC1, and a safety relief device having direct communication with 

the vapor space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and 

the cylinder shall include a collar to protect the cylinder valve.  The cylinder shall incorporate a listed OPD 

(overfill protection device).  Do not store a spare LP-gas cylinder under or near this appliance. Never fill the 

cylinder beyond 80 percent full.  If the preceding information is not followed exactly, a fire causing death 

or serious injury may occur.

!

!

Содержание Prestige PRO BIPRO825RBINSS-3



































Отзывы: