Napoleon NZ-26, Инструкция по установке и эксплуатации

Страница: 12 / 20

W415-0156 / A / 04.09.03
12
INSTALLATION TO BE DONE BY A QUALIFIED IN-
STALLER and must be electrically connected and grounded
in accordance with local codes. In the absence of local
codes, use the current CSA C22.1 CANADIAN ELECTRI-
CAL CODE in Canada or the ANSI/NFPA 70 NATIONAL
ELECTRICAL CODE in the United States.
1. Turn off any elec-
trical power to the fire-
place (if applicable).
Open the lower louvred
control door.
2. Locate the vibration reducing pad (one per blower)
over the two threaded studs, piercing 2 holes into the pad.
The blower must be able to be positioned entirely onto the
pad. If only one blower is used, install on the left hand side
of the fireplace.
ONE BLOWER INSTALLATION:
3. Slide the blower to the back of the fireplace taking
care not to damage the terminals. Position the blower onto
the studs and secure using the lock washers and wing
nuts provided. Pull the leads to the front and right side of
the ashpan housing.
4. Remove the junction box. Use a nut connector to
attach one of the black wires of the variable speed switch
to the black power supply wire.
5. Pass the two blower leads and one thermodisc lead
through the junction box bushing. The thermodisc is lo-
cated inside the outer shell, just above the louvre door.
FIGURE 27. Connect one blower lead to the thermodisc
lead using a nut connector and the other blower lead to the
white power supply wire using a nut connector.
6. Thread the other thermodisc lead through the junc-
tion box bushing and connect to the other black wire of the
variable speed switch using a nut connector. Secure
ground wire (green) to the threaded weld stud located on
the junction box wall. Re-install the junction box. Ensure
that the wires will not interfere with the blower.
DUAL BLOWER INSTALLATION:
3. Slide the first blower to the back of the fireplace tak-
ing care not to damage the terminals. Position the blower
onto the studs and secure using the lock washers and wing
nuts provided. Pull the leads to the front and right side of the
ashpan housing.
4. Slide the second blower into place, position onto the
studs and secure as before.
5. Remove the junction box cover located on the lower
right outside of the unit. Use a nut connector to attach the black
wire of the variable speed switch to the black power wire.
6. Pass the four blower leads and both thermodisc leads
through the junction box bushing. Connect one blower lead
from each blower and one of the thermodisc leads using a
nut connector and connect the other two blower leads to the
white power supply wire using a nut connector.
7. Connect the other thermodisc lead to the black wire
of the variable speed switch using a nut connector. Secure
ground wire (green) to the threaded weld stud located on
the junction box wall. Re-install the junction box. Ensure
that the wires will not interfere with the blower.
Because the blower is thermally activated, when turned
on, it will automatically start approximately 15-45 min-
utes after lighting the fireplace. Use of the blower in-
creases the output of heat.
Drywall dust will penetrate into the blower bearings
causing irreparable damage and must be prevented
from coming into contact with the blower or its com-
partment. Any damage resulting from this condition is
not covered by the warranty policy.
wh
ite
bl
ac
k
bl
ac
k
whi
te
FIGURE 25
FIGURE 26
FIGURE 24
OPTIONAL BLOWER INSTALLATION
If you need to remove the bricks (to lighten the fireplace for
ease of installation, replacement, etc), follow this sequence:
Remove the ashwell grate. This allows the four bot-
tom bricks to be removed first.
Slide out the baffle support bracket from above the front
tube.
4
FIREBRICK REMOVAL
Reaching above the top firebricks and baffles, lift and tape
the bottom flame spreader to the top spreader to ease top
brick and baffle removal and to avoid damaging the fibre
baffle. Remove the three front tubes.
Remove the top firebrick on the right, then the left firebrick.
Remove the baffles, starting with the right side.
Remove the gasket rope. Check the rope for deterioration
and replace if necessary. Remove the rear bricks (pull the
two bricks forward at the centre, and lift the bottom of the
bricks out). Remove the side bricks (tilt the tops inward).