Napoleon Model OS10 Скачать руководство пользователя страница 14

Страница: 14 / 14

TROUBLE SHOOTING

PROBLEM

TEST SOLUTION

SYMPTOM

Flames extinguish
during lighting.

Very cold chimney.
No draft established

- leave door ajar until fire has caught.

Fire extinguishes
during use.

Fuel tank is empty.

- fill tank

Flame is excessely
large, smokey and
sooty.

Fuel adjustment made too
quickly.

- return control knob to

‘1’

; wait for normal combustion.

(catalyser should glow red) Wait 5 to 15 minutes between
each adjustment.

Stove burns noisily,
extinguishes and re-
lights itself.

Burner contains excess fuel

- adjust to lower setting. If problem persists call your in-
staller.

Coke build up no-
ticed.

Excessive air supply.

- adjust draft.

Fuel tank is empty.

Fuel valve is closed.

Main carburetor float not
engaging.

Safety lever will not engage.

Fire extinguishes
once firestarter has
burnt off.

- fill tank

- open valve

- de-press the safety lever

- remove carburetor cover and drain secondary float well.
Check for cause of primary float failure.

Insufficient air supply.

- increase fresh air supply (open door, window; add make-
up air supply)

Downdraft or blockage in
chimney

- check chimney for soot build up. Clean if necessary.

- ensure chimney height is sufficient and cap is not af-
fected by any nearby obstructions.

- room is in negative pressure. Increase fresh air supply.
Check draft with draft meter and adjust if not to require-
ments. See page 4.

Low flame setting incor-
rectly adjusted

- adjust setting. See page 10 for instructions.

Fire smokes.
Soot build up no-
ticed. Flame imbal-
ance.

Oil flow is too low on

set-

ting.

- adjust low flow rate while control is set on ‘

’.

Stove is not level. Flame
imbalance.

Check level. Adjust if necessary.

Catalyser not centered.
Uneven fuel distribution
resulting in secondary air
shortage.

Center catalyser assembly

Содержание Model OS10















Результаты поиска

Содержание Model OS10

Отзывы:

Похожие инструкции для Model OS10

Бренды по названию

Популярные бренды

Napoleon Model OS10, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Model OS10

Отзывы:

Похожие инструкции для Model OS10

Бренды по названию

Популярные бренды