background image

W415-1243 / A / 03.19.15

 37

IOM

12.3  GAS INLET PRESSURE

12.4 LEAK TESTING

12.5  PURGING GAS LINES

H17.2B

IMPORTANT:

  

ALWAYS USE A BACKUP 
WRENCH TO PREVENT TWISTING 
OF THE GAS VALVE. ANY 
STRAINS ON THE GAS VALVE 
CAN AFFECT POSITIONING OF 
THE ORIFICES RELATIVE TO THE 
BURNERS. THIS COULD RESULT 
IN FAULTY BURNER OPERATION.

Install a manual gas shut-off valve and dirt pocket as close to the furnace as possible. Some local codes call 
for the manual gas shut-off valve to be located between 4 feet (1.2m) to 5 feet (1.5m) above 

fl

 oor level to 

prevent tampering by small children. Ensure that the valve is readily accessible.

IMPORTANT:

  

ENSURE 
THAT THE 
GAS VALVE 
IS NOT 
SUBJECTED 
TO HIGH 
PRESSURES.

H3.19

DISCONNECT THE MANUAL SHUT-OFF VALVE AND GAS VALVE DURING ANY 

PRESSURE TESTING THAT EXCEEDS 1/2 P.S.I.G. (3.45 KPA).

WARNING

!  

!  

H17.3.2

The natural gas inlet supply pressure should be 5” to 7” w.c. (7” w.c. recommended). The LP gas inlet supply 
pressure should be 11” to 13” w.c. (12” w.c. recommended). These pressures must be maintained while all other 
gas 

fi

 red appliances are operating at maximum conditions.

IMPORTANT:

  

DO NOT EXCEED 13” W.C. INLET PRESSURE WITH EITHER FUEL.

The gas valve has two adjustable internal regulator for controlling burner manifold pressure. Burner manifold 
high 

fi

 re and low 

fi

 re pressures are listed on the furnace rating plate.

H17.4

All new gas piping installations should be pressure tested as speci

fi

 ed by CAN/CSA-B149.1 & 2, or NFPA 54 

ANSI Z223.1 or ANSI/NFPA 58, 

“Standard for the Storage and Handling of Liquefi ed Petroleum Gases.”

Gas piping that has not been pressure tested, from the manual shut-off valve to the furnace gas valve for 
example, should be leak tested using an electronic combustible gas detector, a commercially prepared leak 
detector, or other locally approved method.

H3.20

NEVER USE A MATCH, TAPER, CIGARETTE LIGHTER, FLAME OR ANY OTHER IGNITION 

SOURCE TO CHECK FOR LEAKS IN A GAS LINE.

FAILURE TO ADHERE TO THIS WARNING CAN CAUSE A FIRE OR EXPLOSION 

RESULTING IN PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.

WARNING

!  

!  

Содержание 9700 SERIES














































































Отзывы: