NAPCO XP-600 - 9-16-1997 Скачать руководство пользователя страница 8

Disarming Your System when Returning

1

Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to 
disarm the system before your  Entry Delay  time expires.

 

Enter your user code. The  Red Armed light will go out, indicating that the system has been  disarmed.
Note: If you make a mistake entering your code, press the 

 key and re-enter the code.

Alarm

 

Indication

If the Red Armed light is flashing rapidly, an alarm occurred while you were away.  Proceed with caution!

 

For your own protection,  leave immediately and call authorities from a neighbor’s phone .

Silencing an Alarm

In the event that the system goes into alarm due to a violated burglary zone, the bell or siren will sound and 
the keypad sounder will also activate. To silence the system, enter your User code. The zone light  of the 
zone which went into alarm will continue to flash until 

 is pressed to reset the alarm memory.

Silencing a Fire Alarm

In the event that the Fire alarm activates due to an violated smoke or fire detector,  the bell or siren will 
sound a distinct pulsating tone. The Red FIRE  light on the keypad will be flashing, and the keypad sounder 
will emit a pulsing tone. If  a Fire Alarm does occur:

1

If a fire is in progress, evacuate the premises immediately!Call the Fire Department from an outside phone.

2

If there is no evidence of a fire, enter your User Code.  The bell or siren  will silence, and the FIRE  light on 
the keypad will stop flashing but will still be lit.

3

Determine which device went into alarm. If you are protected by smoke detectors, the light on the active 
detector will be lit. Once it is determined which smoke detector is in alarm, press 

 to reset  the fire zone.

If  the Fire zone has reset properly, the FIRE light on the keypad should go out in approx. 30 seconds 
If  it does not go out, press 

again in a few minutes. If  the FIRE light still does not go out, call for 

service.

Disarming Your System  / Silencing an Alarm

 8

FIRE

AC

    SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 5

ZONE 6

ZONE 4

 ARMED

Oi218a 
page 8

Tuesday, September 16, 1997 08:28 

Содержание XP-600 - 9-16-1997

















Отзывы: