NAPCO MAGNUM ALERT 825 SYSTEM Скачать руководство пользователя страница 13

The following information is

applicable only where local

ordinance permits use of your alarm
Control Center for fire detection

Controlling Your

Fire Circuit

If your alarm specialist installed

smoke detectors or heat sensing
thermostats, you have 24 hour fire
protection. This optional Fire Pro-
tection Zone is always active, even
though your system may be dis-
armed. An optional Fire Supervision
and Indicator Station on the Control
Center provides the following fire
circuit controls.

AC Power Check

If the yellow AC light on the Fire

Supervision and Indicator Station is
off, the Control Center is not receiv-
ing AC power. Press the spring-

loaded SILENCE & FIRE RESET

switch to shut off the Mini-Sounder.
Check lights to see if there is a

general power outage. If there is,
you will be operating from your
standby battery. When AC power is
restored. the Mini-Sounder will
come back on. Press the spring-
loaded switch again to silence the

Mini-Sounder.

Fire-Zone Check

The Mini-Sounder on the Fire

Supervision and Indicator Station
signals a problem on the Fire Zone.

Press the spring-loaded SILENCE

8 FIRE RESET switch to shut off the

Mini-Sounder. The red TROUBLE
light will come on until the Fire

Zone is cleared. When the zone is

restored, the Mini-Sounder will

signal again to indicate that the

Fire Zone is functional. Press the

SILENCE & FIRE RESET switch
once again to turn off the  Mini-
Sounder.

Fire-Detector Reset

After a fire alarm, the red FIRE

ALARM light will be on. Press the
SILENCE & FIRE RESET switch to
clear the smoke detectors.

Alarm/Battery Test

The fire alarm bell/siren and

standby battery should be tested
weekly. Disarm the Control Center.

Push the BATTERY & BELL TEST

switch down and listen to the bell/
siren. If the alarm sounds weak,
the battery is faulty. Call for service.

Would You Like More

Safety Informatlon?

For information on home fire de-

tection, burn safety, and home fire
safety, contact the National Fire

Protection Association, Public

Affairs Dept.05A, Battetymarch

Plaza, Quincy, MA 02269.

 If there is no Fire Supervision and Indicator Station on your Control

Center and your Fire Zone uses smoke detectors, have your alarm specialist
show you and explain the switch he has installed for resetting the smoke
detectors after an alarm.

13

Содержание MAGNUM ALERT 825 SYSTEM
















Отзывы: