background image

Guide d’Installation sonde E4000 

E4000 probe Installation Guide 

 

www.nano-sense.com 

All Rights Reserved 

Tel: 33 (0)1 41 41 00 02 

page 12/27 

• 

Or Control valve wired (Bi Directional) 

(EEP 4BS: A5-20-03) 

• 

Or Control Generic HVAC Interface (Bi Directional) 

(EEP 4BS: A5-20-10) 

• 

Or Temperature (s measure) 

(EEP 4BS: A5-10-03) 

 
And for temperature cooling control: 

• 

Control valve battery operated (Bi Directional) 

(EEP 4BS : A5-20-01) 

• 

Or Control valve Basic (Bi Directional) 

(EEP 4BS : A5-20-02) 

• 

Or Control valve wired (Bi Directional) 

(EEP 4BS : A5-20-03) 

• 

Or Control Generic HVAC Interface (Bi Directional) 

(EEP 4BS : A5-20-10) 

• 

Or Temperature (s measure) 

(EEP 4BS : A5-10-03) 

 
And, if annex probes are installed: 
• Radon Measurement  

(EEP 4BS: A5-09-06) 

• And or Particles Measurement 

(EEP 4BS: A5-09-07) 

• And or Ozone Measurement 

(EEP 4BS: A5-09-05) 

 
The  control  algorithm  is  similar  to  that  of  relays  (ventilation  1  or  2  speeds)  and  0-10V  output 
(continuous  ventilation)  of  the  analog  module  and  combines  the  CO2,  VOCs  and  humidity 
measurements. 
The  thresholds  setting  of  CO2  and  humidity  (VOC  thresholds  are  regulatory)  is  active  in  EnOcean 
sensor mode as for the analog module. 
 
In EnOcean gateway mode 
EnOcean profiles: 
The  gateway supports  most  of  the EEP2.1  plus  few more telegrams  approved since the publication of 
the EEP2.1 
The only  exceptions  are  CO2 and VOC telegrams,  the probe providing already those data. CO is  also 
voluntarily not handled 
 

7.2.4.4. 

Transmission Range 

As  radio  signals  are  electromagnetic  waves,  the  signal  is  damped  on  its  way  from  the  sender  to  the 
receiver.  That  is  to  say,  the  electrical  as  well  as  the  magnetic  field  strength  is  removed  inversely 
proportional to the square of the distance between sender and receiver (E,H~1/r²). 
 
Beside  these  natural  transmission  range  limits,  further  interferences  have  to  be  considered:  Metallic 
parts, e.g. reinforcements in walls, metallized foils of thermal insulations  or metallized heat-absorbing 
glass,  are  reflecting  electromagnetic  waves.  Thus,  a  so-called  radio  shadow  is  built  up  behind  these 
parts.  
 
Building material used in a building is of paramount importance for the evaluation of the transmitting 
range. For an evaluation of the environment, some guide values are listed: 
 

 

Содержание E4000NG




























Отзывы: