NanoSense E4000NG Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 27

background image

Guide d’Installation sonde E4000

E4000 probe Installation Guide

www.nano-sense.com

All Rights Reserved

Tel: 33 (0)1 41 41 00 02

page 6/27

5.5.

EnOcean Option

For good receiver performance, great care must be taken about the space immediately surrounding the
antenna since this has a strong influence on screening and detuning the antenna. The antenna should be
drawn out as far as possible and must never be cut off. Mainly the far end of the wire should be
mounted as far away as possible (at least 15 mm) from all metal parts, ground planes, PCB strip lines
and fast logic components (e.g. microprocessors). Do not roll up or twist the whip antenna!

5.6.

Gateway EnOcean-KNX Option

Note: Gas sensors must be installed after the connections

and before power on.

6. Install the motherboard into the case

Clip the mother board into the case

EnOcean radio

module

Antenna

EnOcean

module

KNX

module

Case

The arrow on the board
indicates the top position

«
...
4
5
6
7
8
...
»

Содержание E4000NG




























Отзывы:

Нет отзывов

Похожие инструкции для E4000NG

Бренд: rainforest Страницы: 2

Бренд: ECC X-RAY Страницы: 14

Бренд: WalkLAB Страницы: 16

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 60

GranTouch Digital Grand Piano

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 47

YPP-100 Light Piano

Бренд: Yamaha Страницы: 54

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды