NANO NXC Series Скачать руководство пользователя страница 5

5

cycling refrigerated air dryer

R

1

The installer must provide an emergency stop 
bu  on on the unit. They should ensure that 
this is done before the unit is started.

The unit is equipped with protec  ve covers 
for the components. If the unit is installed 
outdoors, it is important to arrange for a can-
opy to protect it from the snow, which could 
cons  tute a risk while using the unit if the fan 
blades freeze. 

Replace all the supply lines of the di

 erent 

power sources which are damaged or missing.

Depending on the version, the refrigerants 
used can be either R407c or R134a. They are 
not harmful unless inhaled. They cons  tute a 
hazard only if they saturate the environment. 
Some 

fl

 uids are 

fl

 ammable under certain 

condi  ons. Refer to the speci

fi

 ca  ons of each 

fl

 uid on the safety data sheet at the end of 

the manual.

This manual is meant for anyone who uses or works on the cycling refrigerated air dryer, mainly the 
operators.  The cycling refrigerated air dryer and this manual are protected by copyright.  Any reproduc  on 
of the same shall be liable for prosecu  on.  All rights reserved by 

nano-puri

fi

 ca  on solu  ons

, par  cularly the 

rights of reproduc  on and distribu  on, as well as transla  on, including those rela  ng to charges of copyright 
infringement.  Any reproduc  on, processing, duplica  on, distribu  on of this document using electronic 
or mechanical means without the prior wri  en authoriza  on of 

nano-puri

fi

 ca  on solu  ons

 is strictly 

prohibited.  This document may have errors and is likely to be modi

fi

 ed with respect to technical features.

All products are supplied with a 30 months manufacturer’s warranty from the date of shipment from the 
factory or 24 months from date of installa  on/start up, whichever occurs 

fi

 rst and installed and maintained in 

accordance with the manufacturers guidelines. Pre-

fi

 lters and non-corrosive upstream piping required.  Only 

genuine service parts should be used and no modi

fi

 ca  ons made.

1.3  

document introduction

1.4 warranty 

guidelines

1.5 general 

warnings

1.6 

basic safety rules

Read the contents of this manual carefully 
before star  ng the units.  

This service and maintenance manual de-
scribes the design, opera  on and the instruc-

 ons for use and maintenance of the units 

manufactured by 

nano-puri

fi

 ca  on solu  ons

.

nano-puri

fi

 ca  on solu  ons

 shall not be liable 

for any damage caused due to non-compli-
ance with the instruc  ons of this manual. 

For the smallest doubts or any clari

fi

 ca  ons 

that may be required, our quali

fi

 ed 

nano-puri-

fi

 ca  on solu  ons 

technicians are available to 

provide all the necessary informa  on. 

In order to make it easier to iden  fy the units, 
it is important to always specify the technical 
features, especially the serial number, which 
are printed on the label on the outside of the 
units.  

The unit should not be operated, even for a 

short period of   me, under condi  ons other 

than the ideal condi  ons.  

A part that does not guarantee safety should 

not be installed.

WARNING:

  This product can expose you to 

chemicals including lead, which is known to 
the State of California to cause cancer and/or 
birth defects or other reproduc  ve harm. For 
more informa  on, go to www.P65Warnings.

Содержание NXC Series

































































Отзывы: