Function introduction
Important:
Read All Instructions Prior to Installation
•
DO NOT install with power applied to device.
•
DO NOT expose the device to moisture.
Safety & Warnings
“Reset” Key: for
network pairing,
touchlink, factory
reset of the dimmer,
turn on/off load
Operation
AC 100-240V power input
Min.Set
L
L
N
N
OUT
L
N
AC 100-240V
Load output
•
ZigBee AC phase cut tunable white dimmer based on latest ZigBee 3.0 protocol
•
100-240VAC Wide Input and Output Voltage
•
Mini size, easy to be Installed into a standard wall box
•
1 Channel Output, Up to 400W
•
Input and Output with Screw Terminals, Safe and Reliable
•
Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
•
Supports self-forming zigbee network without coordinator and add other devices to the network
•
Supports resistive loads and capacitive loads
•
Supports find and bind mode to bind a ZigBee remote
•
Compatible with universal ZigBee gateway products
•
Radio Frequency : 2.4GHz
•
Both
leading
edge
version
and
trailing edge version are available for choosing, default factory setting is trailing edge
•
Enables to control color temperature, light intensity, ON/OFF of phase cut dimming tunable white LED drivers or lamps
•
ZigBee end device that supports Touchlink commissioning
•
Can be controlled by universal push switches
•
Waterproof grade: IP20
•
Supports zigbee green power and can bind max. 20 zigbee green power remotes
Reset
Input Voltage
Output Voltage
Output Current
Product Data
Size(LxWxH)
Compatible Load Types
Load Symbol
Load Type
Maximum Load
Remarks
Due to variety of LED lamp
designs, maximum number
of LED lamps is further
dependent on power factor
result when connected to
dimmer.
Maximum permitted number
of drivers is 200W divided
by driver nameplate power
rating.
Dimmable LED lamps
Dimmable LED drivers
Incandescent lighting,
HV Halogen lamps
Low voltage halogen
lighting with electronic
transformers
100-240VAC
1.8A max
100-240VAC
45.5x45x20.3mm
100W @ 110V
200W @ 220V
200W @ 220V
100W @ 110V
200W @ 110V
400W @ 220V
100W @ 110V
200W @ 220V
1.Do wiring according to connection diagram correctly.
3. Zigbee Network Pairing through Coordinator or Hub
(
Added
to
a
Zigbee
Network
)
Step 1
: Remove the device from previous zigbee network if it has already been added to
,
otherwise
pairing
will
fail
.
Please
refer
to
the
part
"
Factory
Reset Manually
".
Step 2
: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 3:
power on the device, it will be
set into network pairing mode
(connected light flashes twice slowly),
the network pairing mode will last until
the device is added to a zigbee
network.
Step 4
: Connected light will blink 5
times and then stay solid on, then the
device will appear in your controller's
menu and can be controlled through
controller or hub interface.
Input Clusters
•
0x0000: Basic
•
0x0003: Identify
•
0x0004: Groups
•
0x0005: Scenes
•
0x0006: On/off
•
0x0008: Level Control
•
0x0300: Color Control
•
0x0b05: Diagnostics
Output Clusters
•
0x0019: OTA
ZigBee Clusters the device supports are as follows:
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This
receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
L
N
Allowed Inrush Current
Cold Start 75A max.
“Min. Set” Key:
1) to set or delete a minimum
dimming level
2) to set or delete a startup
brightness level
S
1
C
O
M
Push switch input
Min.Set
L
L
N
N
OUT
L
N
AC 100-240V
Reset
S
1
C
O
M
