manualshive.com logo in svg

Nakanishi BMS-4040-RGD-03M, Руководство по эксплуатации

Поделиться
Скачать
Nakanishi BMS-4040-RGD-03M Скачать руководство пользователя страница 10

10

Table 3.  Overhang and Speed

Overhang (mm)

Max. Speed (min

-1

)

20

N x 0.5

25

N x 0.3

50

N x 0.1

N=Max. Operating Speed with 13mm overhang.

Fig. 20

13

Trouble

Cause

Inspection/Corrective Action

Spindle does not 

run.

The ball bearings are damaged.

Replace the ball bearings.

(Return to NAKANISHI dealer service.)

Motor is broken.

Replace the motor.

(Return to NAKANISHI dealer service.)

Overheating 

during rotation.

Cutting debris has contaminated 

the  ball  bearing,  and  the  ball 

bearing is damaged.

Replace the ball bearings.

(Return to NAKANISHI dealer service.)

Low air pressure.

Check air hose connection and air pressure. 

Abnormal vibration 

or noise during 

rotation.

Using bent tool.

Replace the tool.

Cutting debris has contaminated 

the ball bearing.

Replace the ball bearings.

(Return to NAKANISHI dealer service.)

The ball bearings are worn.

Tool slippage.

Collet or collet nut are not

correctly installed.

Check and clean the collet and collet nut. And, 

tighten the collet accurately again.

The collet and the collet nut are 

worn.

Replace the collet and the collet nut.

High run-out.

The tool is bent.

Change the tool.

Collet nut is not correctly installed. Secure the collet and the collet nut correctly.

The collet and the collet nut are 

worn.

Replace the collet and the collet nut.

Inside of the spindle is worn.

Replace the spindle shaft.

(Return to NAKANISHI dealer service.)

Contaminants inside the collet and 

the collet nut or the spindle.

Clean the collet, collet nut and the inside of the 

taper and spindle.

The ball bearings are worn.

Replace the ball bearings.

(Return to NAKANISHI dealer service.)

13

. TROUBLESHOOTING

If a problem or concern occurs, please check the following prior to consulting your dealer.

OM-K0697E000_BMS-4040-RGD Series B5 中綴じ_EN_181016.indd   10

2018/10/16   9:13:04

Содержание BMS-4040-RGD-03M













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды