6.1
switching on and off
Wake av2 from standby (power switch on
).
Handset: press and hold
standby
.
Front panel: press and hold
input
or
mode
.
Put av2 to sleep (power switch on
)
.
Handset: press and hold
standby.
Front panel: press both
input
and
mode
.
6.2
input setup routine
Enter setup mode.
Handset: press
menu
followed by
i/p
.
Front panel: press and hold
input
.
Scroll up or down parameter list.
Handset: press
2
or
8
Front panel: press
input
or
mode
.
Adjust setting
Handset: press
4
or
6
Front panel: rotate rotary control
three
setup parameters
parameter settings
6
6.0 av2 basics and quick setup
Installation of the
av2
requires two setup routines to be carried out -
input setup
and
speaker setup.
These routines configure the
av2
for the source equipment and
loudspeakers it is to be used with and specify some signal decoding options. Some setup
parameters are dependent on the state in which the
av2
was last shut down so setup may
be simplified if the
av2
is returned to its setup defaults. See
Section 11
for notes on
restoring setup defaults. Information on
av2
decode modes and capabilities can be found
starting in
Sections 10.2 - 10.6
The following diagrams provide a short-cut through the setup routines. They can also be
used in conjunction with the detailed notes in
Sections 9
and
10
where setup choices
display legends are more fully explained.
Exit setup mode.
Handset: press
menu
followed by
i/p
.
Front panel: press and hold
input
.
mode
2
8
8 c h . . . a n 1 . . . s c d
one
four
two
mode
input
mode
input
standby
standby
on
or
or
or
input
menu
i/p
or
input
menu
i/p
or
input
4
6
or
or
or
and
off
versatile analog input 1 (select source, multi)
V i 2
V i 1
- - - . . . a n 2 . . . s c d
versatile analog input 2 (select source, multi)
A N 3
- - - . . . a n 3 . . . s c d
analog input 3 (select source)
A N 4
- - - . . . a n 4 . . . s c d
analog input 4 (select source)
a n 5
- - - . . . a n 5 . . . s c d
analog input 5 (select source)
a n 6
- - - . . . a n 6 . . . s c d
- - - . . . o p 1 . . . s c d
- - - . . . o p 2 . . . s c d
analog input 6 (select source)
o p 1
optical digital input 1 (select source)
o p 2
- - - . . . c o 1 . . . s c d
- - - . . . c o 2 . . . s c d
r c 5
d a t
optical digital input 2 (select source)
c o 1
coaxial digital input 1 (select source)
c o 2
coaxial digital input 2 (select source)
e x t
remote control
note
Analog inputs 1 and 2 can be
combined to provide one 8
channel or 6 channel input. In
either case input 2 is then
unavailable. For a complete
description of this facility see
Sections 7 and 9.
note
The final three stages of the
input setup routine provide
adjustment for three Dolby
Surround Pro Logic II music
programme decode parameters.
It is not necessary to set these
parameters initially. See
Section 9
for detailed
information on these decode
parameters.
note
With
DAT
(data) selected for
the EXT parameter RC5 (remote
handset) control is disabled.
RC5 can be re-enabled using
the front panel controls.
Dolby Surround Pro Logic II “Panorama”
Dolby Surround Pro Logic II “Dimension”
Dolby Surround Pro Logic II “Centre Width”
D
w
P a n
o f f
o n
0 0 - 0 7
0 0 - 0 6
Содержание NAP V175
Страница 1: ...O W N E R S M A N U A L AV S y s t e m ...
