6701 Shellmound Street
|
Emeryville, CA USA 94608
T
510.652.2411 |
F
510.652.5075 |
www.nady.com
Connecting the CM-100
The CM 100 can be used in live or studio alignment
applicatoins or studio recording. It must be powered by
48V phantom power (such as supplied by the optional Nady
SMPS-1 phantom power supply or a mixing console/alignment
device equipped with phantom power), and amplified by a
microphone pre-amp (such as built into a mixer, or a stand-
alone unit).
Note:
Make sure to set the pre-amp to the proper gain level—too much gain may
distort subsequent amplifiers and too little may result in a noisy signal)
The CM 100 can be connected to your mixer or phantom
power supply using a standard balanced 3-pin XLR
microphone cable. Before connecting to a mixer directly, turn
the channel to which you’re connecting to its lowest gain
setting. If you are
using the Nady SMPS-1 Phantom Power Supply, connect
in the following order:
1. Connect the CM 100 to the SMPS-1
2. Connect the SMPS-1 Signal Output to your mixer
3. Connect the SMPS-1 to the AC power supply (115-230VAC)
4. Turn on the SMPS-1 Power ON/OFF switch
Slowly turn up the channel gain in your mixer to the
desired level.
Using the Foam Windscreen
The CM 100 is supplied with a foam windscreen (FW-1/100).
This windscreen fits over the grill portion of the microphone
and is designed primarily to decrease bass rumble (from wind
noise pickup) during outdoor live or recording use. It is also
useful in keeping mouth spray out of the microphone head.
The FW-1 or other windscreen should be used whenever
someone is close miked to both protect the microphone and
to also eliminate “popping” sounds from percussive breath
sounds.
Note:
Be aware that the foam windscreen will slightly attenuate the high frequency
response of the microphone.
Service Information
In the U.S.
If you are experiencing operational problems with your system, please refer to the Support page at www.nady.com for assistance. Should your wireless
system require service, please contact the Nady Service Department at (510) 652-2411 to obtain a Return Authorization (R/A) Number and service quote (if out of
warranty). Make sure the R/A Number is clearly marked on the outside of the package that you are returning.
If your unit is out of warranty, please enclose a cashier’s check or money order (or pay by credit card) per instructions by the Nady Service Department. Ship
your unit prepaid to: Nady Systems, Service Department, 6701 Shellmound Street, Emeryville, CA 94608. Include a brief description of the problem you
are experiencing. For service of a unit under warranty, please follow the instructions in the following section.
Outside the U.S.
For service or warranty matters please contact the Nady distributor in your country through the dealer/store from which you purchased this product.
Do not attempt to service this unit yourself as it can be dangerous and will also void the warranty.
One Year Warranty
Nady Systems, Inc. warrants to the original consumer purchaser (U.S.A. only) that your unit is free from any defects in material or workmanship for a period of
one year from the date of purchase. If any such defect is discovered within the warranty period, Nady Systems, Inc. will repair or replace the unit free of charge,
subject to verification of the defect or malfunction upon delivery or shipping prepaid to Nady Systems.
Important:
Please do not return our product to the store where it was purchased. Nady Systems, Inc. accepts the responsibility of keeping you a satisfied customer.
This warranty does not apply to defects or physical damage resulting from abuse, neglect, accident, improper repair, alteration, or unreasonable use of the
unit resulting in cracked or broken cases or parts, or units damaged by excessive heat, and does not apply to batteries or damage caused by leaking batteries.
This warranty does not cover finish or appearance items nor items damaged in shipment en route to Nady Systems Inc. for repair. You must include proof of date
and place of purchase (i.e. photocopy of your bill of sale) or we cannot be responsible for repairs or replacement. If factory service is required, you must contact
our Service Department at 510/652-2411 for a return authorization (RA) number. Make sure the RA number is clearly marked on the outside of the package.
Nady Systems, Inc. will not repair nor be held responsible for any units sent without proper identification and return address or RA number clearly marked
on the package.
For service, ship units prepaid to: Nady Systems, Inc., Service Department, 6701 Shellmound St., Emeryville, CA 94608.
Operation
