2 6
2 6
2 6
2 6
2 6
USING THE HTR 2 REMOTE CONTROL
• Controls up to 8 devices.
• 44 function keys.
• Learns up to 352 commands.
• Records up to 44 macros with a maximum of 64 commands each.
• Configurable punch-through.
• Key illumination with programmable timeout.
• Upgradable.
• Contains pre-programmed library of NAD remote codes.
The NAD HTR 2 is ready to operate the T 753 receiver right out of the box, but it is really eight remotes in
one. Each of the 8 Device Selector keys at the top of the handset can call up a new “page” of remote-
control codes to be transmitted by the remaining 44 keys. You may “teach” codes from any infrared-remote-
controlled component, regardless of brand, to any or all of these. Obviously, the most logical system is that
you teach the codes from your DVD player to the [DVD] Device Selector “page,” your television’s codes to
the [TV] “page,” and so on, but there is no required scheme: You may load any commands to any key on
any page (see “Learning Codes From Other Remotes,” below).
The HTR 2 is already preprogrammed with a full complement of commands for the T 753 receiver on its
[AMP] Device Selector page, and as well as with library commands to operate most NAD-brand DVD, CD, or
TAPE components on the corresponding Device Selector “pages.” These default commands are permanent:
Even if you teach the HTR 2 new commands to take their place, the underlying library commands remain in
place and can easily be recalled should you add an NAD component to your system later (see “Delete
Mode”, below).
NOTE
: For use with the T 753, it should not be necessary to re-program any keys on the HTR 2 [AMP]
page. However, in order for the HTR 2 to control your specific NAD-brand components you may need to
load one or more different code-libraries; see “Loading Code Libraries,” below.
CONTROLLING THE T 753
CONTROLLING THE T 753
CONTROLLING THE T 753
CONTROLLING THE T 753
CONTROLLING THE T 753
The HTR 2 is divided into two main sections. Eight Device Selector keys at the top—[AMP], [DVD,] [TV,] and
so on—set the handset’s remaining keys to a “page” of commands to control a particular component. A
Device Select key determines only what component the HTR 2 will command; it does not perform any
function on the receiver. All of the remaining keys are function keys that can “learn” control codes from
virtually any infrared remote controller, allowing you to teach the codes of your equipment, regardless of
brand, to the HTR 2.
However, the HTR 2 is already preprogrammed to operate the T 753. All of the function keys on the [AMP]
Device Selector “page” perform T 753 functions. (The HTR 2 can also command many other NAD compo-
nents, from its [DVD,] [CD,] [TUNER,] and [TAPE] pages.)
It is important to note that certain HTR 2 keys perform different functions depending on the selected Device
Selector “page.” The color of the Device Selector key-labeling corresponds to the labeling of the function
keys. Most centrally, the red [AMP] Device Selector “page” corresponds to the red input-select labeling
adjacent to the numeric keys: When the HTR 2’s [AMP] Device Selector page is active, these keys select the
receiver inputs. Similarly, the purple [DVD] Device Selector “page” corresponds to several purple labels, the
green [TV] page to green labels, and so on.
LEARNING CODES FROM OTHER REMOTES
LEARNING CODES FROM OTHER REMOTES
LEARNING CODES FROM OTHER REMOTES
LEARNING CODES FROM OTHER REMOTES
LEARNING CODES FROM OTHER REMOTES
Begin by positioning the HTR 2 “nose-to-nose” with the source remote so the two devices’ infrared windows
are about 2 inches apart.
• Enter Learning Mode: On the HTR 2, simultaneously press-and-hold for 3 seconds both a Device Selector
key and the [•] “record” key (just below the [DISP] key), until the Learn LED at the center of the HTR 2
turns steady green.
• Press the HTR 2’s function key you wish to teach a command; the Learn LED will turn amber.
• Press-and-hold the function key on the source remote: The HTR 2’s Learn LED will flicker amber for a
second or two, then turn solid green. The command is learned.
• Press the HTR 2’s Device Selector key again to exit the learning mode.
If the Learn LED does not flicker amber you may need to vary the distance between the remotes.
If the Learn LED turns red rather than green, that particular command of that source remote command
could not be learned.
Cancel Operation:
You can cancel configuring a key, by pressing the active Device Selector key before the learn is complete;
the Learn LED will turn red.
Example: Learning “DVD Pause”:
Position the HTR 2 and your DVD player’s remote as described above.
• On the HTR 2, simultaneously press-and-hold [DVD] and [•]; the Learn LED turns steady green.
• Press the HTR 2’s [
| |
] (pause) key; the Learn LED turns amber.
• Press-and-hold the DVD player’s remote’s pause key; the HTR 2’s Learn LED flickers amber and then
turns solid green. The command is learned.
• Press [DVD] again to exit the learning mode.
SPECIFICA
SPECIFICA
SPECIFICA
SPECIFICA
SPECIFICATIONS
TIONS
TIONS
TIONS
TIONS
Содержание T753
Страница 1: ...Owner s Manual ENGLISH ...
