NAD M23 Скачать руководство пользователя страница 8

ENGLISH

8

WARNING

 

The front panel 

(Standby) button is disabled as long as the male 

plug of the mono cable (with or w12V DC) is connected to M23’s 
+12V TRIGGER IN. Unplug the mono cable for the M23 to be powered up 
from standby mode to operating mode and vice-versa using the front 
panel 

(Standby) button.

6  GAIN LEVEL (LOW/MID/HIGH)

• 

Gain level adjustment allows the source to be played back at the 
same volume level so you don’t need to adjust the volume every 
time you change to a new source.

• 

The Gain Level of the M23 can be set to any of the following - LOW 
(19dB), MEDIUM (24dB) and HIGH (29dB).  

7  BRIDGE MODE

M23 can be configured to be MONO (ON/BRIDGE), more than doubling its 
output power. This way, M23 can be used as part of a high power stereo or 
home-theatre system, by connecting additional power amplifiers.

• 

In BRIDGED MODE (switch at ON/BRIDGE setting), M23 will produce 
approximately 700W into an 8 ohm loudspeaker. In this mode, the 
amplifier sections will react as though the speaker impedance has 
been halved. Low impedance speakers (under 8 ohms) are not 
recommended when using Bridge Mode as these may cause the 
amplifier’s thermal cut-out to operate if played at high levels.

• 

Set the BRIDGE MODE switch to ON/BRIDGE position and connect 
the speaker to the terminals marked “L +” and “R-” ensuring that the 
“L+” is connected to the “+” terminal of your speaker and the “R-” is 
connected to the speaker’s “ - ” terminal.

• 

Connect the source to Left Audio Input ports only. Do not connect 
anything to Right Audio Input ports when Bridge Mode is selected.

• 

Set BRIDGE MODE switch to OFF/STEREO for normal operation.

8  LED LEVEL (DIMMER) 

• 

Press repeatedly to turn off or adjust the brightness level of the 
Power indicator.

9 POWER

• 

The AC mains power to M23 is regulated by the POWER switch. When 
the POWER switch is set to ON position, M23 goes to standby mode as 
shown by the amber status condition of the Power indicator. Press 

o

 

(Standby) button to power up M23 from standby mode.

• 

If you intend not to use the M23 for long periods of time (such as 
when on vacation), switch off the POWER switch.

• 

The 

o

 (Standby) button cannot activate M23 with the rear panel 

POWER switched off.

10  AC MAINS INPUT

• 

M23 comes supplied with a detachable power cord. 

• 

Ensure that the supplied power cord’s female connector end is 
firmly secured to M23’s AC Mains input socket and the male plug 
connected to the mains power source.

• 

Always unplug first the power cord from the mains power source 
before disconnecting the female connector end from M23’s AC 
Mains input socket.

11  FUSE HOLDER

• 

Only qualified NAD service technicians can have access to this fuse 
holder.  Opening this fuse holder may cause damage thus voiding 
the warranty of your M23.

12  GROUND TERMINAL

• 

Ensure M23 is plugged-in to a grounded AC wall outlet.

• 

If a separate earth ground is necessary, use this terminal to ground 
your M23. 

• 

M23 can be connected to ground by connecting a ground lead 
wire or similar to this terminal. After insertion, tighten the terminal 
to secure the lead.

IDENTIFICATION OF CONTROLS

REAR PANEL

Содержание M23











Отзывы: