NAD C 368 Скачать руководство пользователя страница 16

AUTO SENSE 

Auto sense feature enables the C 368 to wake up from standby mode 
when triggered by network connected App or active source input.

ON
• 

Unit wakes up from standby mode when triggered by network 
connected App or active source input.

• 

Except for analog input, the unit will power up to the Source that 
activated the unit to operating mode.

• 

When the unit is triggered by an active analog input, the unit will 
always power up to Line 1. 

OFF
• 

Unit remains at standby mode even if it is triggered by network 
connected App or active source input.

Refer also to table below about “OPERATING MODE TRIGGER POINTS”.

OPERATING MODE TRIGGER POINTS

SETTINGS

OPERATING MODE TRIGGER

Auto Standby: On

Network Standby: On

Auto Sense: On

Unit switches back to operating mode by

•  resuming activity at network connected app.

•  an active source input. 

•  pressing front panel Standby button or SR 9 remote 

control’s [ON] button.

Auto Standby: On

Network Standby: Off

Auto Sense: On

Unit switches back to operating mode by

•  an active source input. 

•  pressing front panel Standby button or SR 9 remote 

control’s [ON] button.

Auto Standby: On

Network Standby: On/Off

Auto Sense: Off

•  Unit remains at standby mode even if it is triggered 

by network connected App or active source input.

•  Unit can only be switched back to operating mode by 

pressing front panel Standby button or SR 9 remote 

control’s [ON] button.

IR CHANNEL

The C 368 has the capability to operate via Alternate IR channel. This is 
useful if you have two NAD products that can be operated by similar 
remote control commands. With alternate IR Channel, two different NAD 
products can be controlled independently in the same zone by setting 
each one to a different IR channel.

IR Channel Assignment

The C 368 and the SR 9 remote control must be set to the same channel. 

To change the IR Channel on the C 368

While at IR Channel menu, use the [

a/s

] to select through Channel 0 to 

Channel 3. Press [ENTER] to select preferred IR Channel setting. C 368 IR 
Channel is defaulted to Channel 0. 

To change the IR Channel on the SR 9 remote control
• 

Include a channel number before the library code. For SR 9, library code 
“10” is the default library table for “AMP” device. To select this “AMP” 
library table for Channel 0, retain the library code “10” (or “010”). 

• 

If you want to load the “AMP” library table on ”Channel 1” prefix the 
library code with “1” to indicate association with “Channel 1”. Load then 
the “AMP” library table using the code “110”. Repeat the same for MP 
(130) and TUNER (140).

SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE 

NAD C 368 and NAD C 390DD are both defaulted to Channel 0. If [OFF] 
button is pressed on the SR 9 remote control (or AVR 4 remote control for 
the C 390DD), both products will go to standby mode. Press [ON] and both 
products will power up from standby mode.

To prevent both products from simultaneously going in and out of standby 
mode along with other common commands, set each one to a different 
IR channel. In this setup, we will keep C 390DD and AVR 4 remote control 
defaulted to “Channel 0”. As for C 368, we will assign it to “Channel 1”; the 
same applies to SR 9.

Set C 368 and SR 9 to “Channel 1” via the following procedure.

C 368

While at “IR Channel” menu, use the [

a/s

] to go to “Channel 1” setting. Press 

[ENTER] to select “Channel 1”. 

SR 9
• 

Press and hold [AMP] in the DEVICE SELECTOR section of the SR 9. 

• 

While holding down the device button [AMP], press “1”, “1” and “0” using 
SR 9’s numeric buttons. 

• 

Press [ENTER] while still holding down the device button [AMP]. The 
AMP device selector will flash once to indicate that the library input is 
successful. 

With both C 368 and SR 9 set to “Channel 1”, the C 368 can now be 
remotely controlled independent of the C 390DD.

NOTE

 

Performing a Factory Reset for C368 or SR 9 will restore their respective 
IR channel setting to “Channel 0”.

OPERATION

USING THE C 368

IR Channel

Settings

Source Setup

Channel 0

Settings

Auto Sense

Settings

Source Setup

Off

Settings

16

ENGLISH

FR

ANÇ

AIS

ESP
AÑOL

IT

ALIANO

DEUT

SCH

NEDERL

ANDS

SVENSK

A

РУ

ССКИЙ

Содержание C 368























Отзывы: