BLUETOOTH AS A SOURCE
Initiate pairing of your Bluetooth device with C 328 by following below
procedure.
1
Ensure that the Bluetooth antenna is connected to the BT antenna
terminal at the rear panel. Ensure also that your Bluetooth is active or
turned ON.
2
Using your iOS, Android or your Bluetooth device, go to Settings –
Bluetooth and then scan for Bluetooth devices.
3
Select the unique device ID of your C 328 among the available devices
listed in your Bluetooth settings. Pair or connect together your C 328
and Bluetooth device.
4
Upon successful pairing of your Bluetooth device and C 328, you may
start music playback from your Bluetooth device.
The front panel display indicator “BT” will illuminate when music is
streamed via Bluetooth connection.
UNPAIR BLUETOOTH CONNECTION
Undertake below procedure to unpair or disconnect Bluetooth connection
to C 328.
1
While at operating mode, press and hold “
4
” button of AMP 3 remote
control until “BT” begins to flash in the front panel display.
2
Release “
4
” button as “BT” flashes for three times. Bluetooth connection
is cleared and available again for pairing or connection.
AUTO STANDBY
Auto Standby feature is an integral feature of C 328 that conforms to
European ecodesign regulations. The C 328 can be setup to automatically
go to standby mode if there is no user interface interaction or no audio at
current source within 20 minutes. Follow below procedure to enable or
disable auto standby mode.
Enable/Disable Auto Standby mode
At operating mode, press and hold together SOURCE
s
and BASS EQ
buttons until “ON” is shown in the front panel display. “ON” is the default
auto standby mode setting.
Repeat the same to disable Auto Standby mode but this time the display
should show “OFF”.
AUTO STANDBY MODES
There are two types of auto standby mode with auto standby set to ON.
ECO Mode
Activate ECO mode:
Press and hold front panel Standby button until the
display shows flashing “OFF”. C 328 will then go to ECO auto standby mode.
•
ECO standby mode switches the C 328 to standby mode at lowest
power consumption (less than 0.5W).
•
At ECO standby mode, the C 328 can only be switched to operating
mode by the following method.
-
Press the front panel Standby button or AMP 3 remote control’s
[ON] button.
-
Resume playback of analog or digital sources.
Control Mode
•
If there is no user interface interaction and no active source input
within 20 minutes, the unit switches to standby mode at reduced
system performance level (less than 2W).
•
Bluetooth connection is maintained at Control Mode.
•
At Control Mode, the C 328 can be switched back to operating mode
using any of the following methods:
-
Resume playback of analog or digital sources.
-
Play paired Bluetooth source.
-
Rotate VOLUME knob.
-
Press any of the
a
SOURCE
s
or BASS EQ buttons.
-
Press front panel Standby button or AMP 3 remote control’s [ON]
button.
AUTO SENSE
Auto sense feature enables the C 328 to wake up from standby mode
when triggered by an active (digital/analog) audio source input.
Enable/Disable Auto Sense mode
While in operating mode, press and hold BASS EQ button until “A” (On) is
shown in the front panel display.
Repeat the same to disable Auto Sense mode but this time the display
should show “-” (Off).
A (On):
Unit wakes up from standby mode when triggered by active audio
source input.
- (Off):
Unit remains at standby mode even if it is triggered by active audio
source input.
IMPORTANT NOTES
With Auto Sense mode set to “On”, the unit cannot go to standby
mode as long as there is an active audio source input. Undertake the
following to enable the unit to go to standby mode with Auto Sense set
to “A” (On).
• Shut down or pause your audio source input(s)
• Set Auto Sense setting to ”-“ (Off)
OPERATION
USING THE C 328
9
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ
