NACD 11.5 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

background image

North American Clutch & Driveline

Rockford, Illinois

Phone: (800) 383-9204

(815) 282-7960

Fax (815) 282-9160

www.naclutch.com

Power Take-Off Installation to Engine or Driving Member

1.

2.

3.

4.

5.

Engine and/or power take-off failure will result form any excessive preload
on components.

6.

Clean the power take-off housing flange, flywheel housing flange, and pilot bearing
bore or any debris. Install two alignment studs into the flywheel housing to assist
with the power take-off installation.

Install 2 or 3 guide studs in the flywheel housing. Position the power take-off against
the flywheel housing, carefully aligning the main shaft pilot with the pilot bearing bore
and the driving plates with the drive ring.

Secure the power take-off housing to the flywheel housing with 12 hex-head cap-
screws. Torque the capscrews to the proper specifications given in Torque Values
for Fasteners.

Note: Power take-off housing to flywheel housing attachment screws must be grade
5 or better.

Rap the output end of the clutch shaft with a soft hammer to remove any preload on
the main bearings and/or pilot bearing.

Note: This step must not be omitted. Bearing failure may result.

Measure the crankshaft end play again. The measurement must be the same exact
value as recorded from Step 1 under Preliminary Checks. Locate and correct the
source or preload if the end play is not the same value.

Install the key on the output shaft and install the drive sheave, chain sprocket, or u-
joint flange as the application requires.

Note: A power take-off support plate mounted at the output bearing retainer is con-
sidered mandatory for this unit.

9

«
...
11
12
13
14
15
...
»

Содержание 11.5

































Отзывы:

Нет отзывов

Похожие инструкции для 11.5

Бренд: Silverline Страницы: 2

Бренд: EINHELL Страницы: 24

Бренд: Harbor Breeze Страницы: 3

Бренд: Woodstar Страницы: 116

XTRIC 363000 80S

Бренд: GARANT Страницы: 116

Бренд: Neilsen Страницы: 2

Бренд: Matco Tools Страницы: 10

Бренд: BGS technic Страницы: 16

Ax-Press 25 22 V ACC

Бренд: REMS Страницы: 168

Бренд: Narex Страницы: 32

PPH SS 670 PENDULUM ACTION JIGSAW

Бренд: Parkside Страницы: 12

Бренд: Wel-Bilt Страницы: 4

Бренд: Uniflex Страницы: 44

Бренд: Steel City Страницы: 32

Бренд: Baileigh Industrial Страницы: 44

Бренд: Fohrenbach Страницы: 8

Бренд: Kett Страницы: 6

Бренд: Sealey Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды