Mylex Disk Array controller Software Kit 2.01 Скачать руководство пользователя страница 63

Страница: 63 / 172

Windows NT

Manual No. 771929

3-15

W
I
N
D
O
W
S
N
T

The Select Components dialog box is displayed as shown in Figure 3-22.
At this point you will select the component(s) you wish to install.

Figure 3-22. Select Components to Install

6. To select Global Array Manager Server for installation, click the white

box to check the Global Array Manager Server option.

☛

Note

You may also choose to install Global Array Manager
Client at this time. If you wish to install both GAM
Server and GAM Client, please refer to the Client
documentation to install the Global Array Manager
Client.

Содержание Disk Array controller Software Kit 2.01













































































































































































Результаты поиска

Содержание Disk Array controller Software Kit 2.01

Отзывы:

Mylex Disk Array controller Software Kit 2.01, Руководство по установке и инструкция пользователя, Страница: 63 / 172

Результаты поиска

Содержание Disk Array controller Software Kit 2.01

Отзывы: