MyBinding Afinia Label L701 страница 50 Скачать руководство пользователя

Страница: 50 / 85

Printer Maintenance

Replace

Cutter

Assembly

If replacing the cutter assembly, continue with the following steps.
1. Use a small flat‐head screwdriver to release the wire harness connector for the

cutter assembly (labeled CUTTER MODULE) and separate it (

Figure 9

2. Remove the two screws (a) securing the cutter assembly and remove the

assembly (

Figure 10

Figure

Cutter

assembly

clamshell

3. Line up the mounting holes and guides on the new cutter assembly and the front

of the clamshell. Insert and tighten the screws to secure the assembly.

4. Make sure the cutter is at the side of the cutter assembly.

5. Reattach the wire harness connector (labeled

CUTTER MODULE

) for the cutter

assembly at the side of the clamshell (

Figure 9

sure

reattach

the

correct

connector

for

the

cutter

assembly.

6. Gently pull the black cable out of the notches at the bottom corners of the cutter

assembly so that the output module can be installed.

notch

cable

cutter

guide

notch
for

cable

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Содержание Afinia Label L701






















































































Результаты поиска

Содержание Afinia Label L701

Отзывы:

Похожие инструкции для Afinia Label L701

Бренды по названию

Популярные бренды

MyBinding Afinia Label L701, Инструкция по эксплуатации

Результаты поиска

Содержание Afinia Label L701

Отзывы:

Похожие инструкции для Afinia Label L701

Бренды по названию

Популярные бренды