30
EN
M1.1.MWM1200.NLFREN 23082018
4�3 Measure resistance
1.
Connect the black test lead to the COM terminal and the red lead to the VΩHz terminal.
2. Turn the rotary switch to , and the display will show “OL”.
3. Touch the probes to the desired test points of the circuit to measure the resistance.
4. Read the measured resistance on the display.
*Disconnect circuit power and discharge all capacitors before you test resistance�
*Do not input voltage at this setting�
4�4 Test for continuity
1.
Connect the black test lead to the COM terminal and the red lead to the VΩHz terminal.
2. Turn the rotary switch to , press SELECT once to toggle to the Continuity mode.
3. Touch the probes to the desired test points of the circuit.
4.
The built-in beeper will beep when the resistance is lower than 50 Ω, which indicates a short circuit.
*Do not input voltage at this setting�
4�5 Test diodes
1.
Connect the black test lead to the COM terminal and the red lead to the VΩHz terminal.
2. Turn the rotary switch to , press SELECT twice to toggle to the Diode mode.
3. Connect the red probe to the anode side and the black probe to the cathode side of the diode being tested.
4. Read the forward bias voltage value on the display.
5. If the polarity of the test leads is reversed with diode polarity or the diode is broken, the displays shows “OL”.
*Do not input voltage at this setting�
*Disconnect circuit power and discharge all capacitors before you test diode�
4�6 Measure capacitance
1.
Connect the black test lead to the COM terminal and the red lead to the VΩHz terminal.
2. Turn the rotary switch to , press SELECT three times to toggle to the Capacitance mode.
3. Connect the red probe to the anode side and the black probe to the cathode side of the capacitor being tested.
4. Read the measured capacitance value on the display once the reading is stabilized.
*Disconnect circuit power and discharge all capacitors before you test capacitance�
4�7 Measure frequency
1.
Connect the black test lead to the COM terminal and the red lead to the VΩHz terminal.
2. Turn the rotary switch to , push SELECT once to toggle to the AC V mode, then push Hz/Duty once to toggle to the
Frequency mode (applies to low frequency with high voltage), or turn the rotary switch to
HZ
(applies to high frequency
with low voltage).
3. Touch the probes to the desired test points.
4. Read the measured frequency value on the display.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, and the display
will show
“
”
.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
Test for Continuity
1. Connect the black test lead to the COM
Terminal and the red lead
to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, press SELECT
once to toggle to the Continuity Mode.
3. Touch the probes to the desired test points of
the circuit.
13
*Disconnect circuit power and discharge all
capacitors before you test resistance.
*Do not input voltage at this setting.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, and the display
will show
“
”
.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
Test for Continuity
1. Connect the black test lead to the COM
Terminal and the red lead
to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, press SELECT
once to toggle to the Continuity Mode.
3. Touch the probes to the desired test points of
the circuit.
13
*Disconnect circuit power and discharge all
capacitors before you test resistance.
*Do not input voltage at this setting.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, and the display
will show
“
”
.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
Test for Continuity
1. Connect the black test lead to the COM
Terminal and the red lead
to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, press SELECT
once to toggle to the Continuity Mode.
3. Touch the probes to the desired test points of
the circuit.
13
*Disconnect circuit power and discharge all
capacitors before you test resistance.
*Do not input voltage at this setting.
Measure Resistance
1. Connect the black test lead to the COM
Terminal and the test lead to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, and the display
will show
“
”
.
3. Touch the probes to the desired test points of
the circuit to measure the resistance.
4. Read the measured resistance on the display.
Test for Continuity
1. Connect the black test lead to the COM
Terminal and the red lead
to the V
Ω
Hz
Terminal.
2. Turn the rotary switch to
, press SELECT
once to toggle to the Continuity Mode.
3. Touch the probes to the desired test points of
the circuit.
13
*Disconnect circuit power and discharge all
capacitors before you test resistance.
*Do not input voltage at this setting.
6
Function Buttons
①
②
①
Selects alternate measurement modes on a
rotary switch setting, including:
1. DC V/AC V
2. Resistance/Continuity/Diode/Capacitance
3. Celsius/Fahrenheit
4. DC
μ
A/AC
μ
A
5. DC A/AC A
②
When the rotary switch is at , push
SELECT once to toggle to AC V testing
mode, then push this button to enter
Frequency/Duty Cycle (with high voltage)
testing mode.
When the rotary switch is at , push this
button to enter Frequency/Duty Cycle (with
low voltage) testing mode.
③
④
copyrighted
document
- all
rights
reserved
by
FBC
