MVP RTM-HVUPS Seires Скачать руководство пользователя страница 19

Страница: 19 / 31

High Volume/Output RTM Systems Operations Manual

Page | 19

Innovator II Control Panel

Control Name

Type of Control

Function

CAT/OP

Indicator Light

Will turn red if overpressure state exists.

RGA Alarm

Indicator Light

Will turn red if gel alarm timer has expired.

Flush Button

Push Button

Press this button to operate the flush cycle

Mold Pressure

Guard

Preset Level Gauge

Displays signal air pressure being supplied to the Mold Pressure

Guard (MPG) control.

Mold Pressure

Guard

Regulator

Use this to adjust the MPG control signal air pressure.

Inject Button

Push Button

Press this button to start the machine in inject mode.

Recirculate Button Push Button

Press this button to start the machine in recirculation mode.

Stop Button

Push Button

Press this button to stop the machine in injection, recirculation, or

flush mode.

Stroke Count

Counter

Displays the current number of strokes the pump has performed.

Stroke Count

Preset Count

Counter

Displays the number of strokes at which the unit will shut down

when reached.

Stroke Count Digit

Modifiers

Spin Buttons

Click up or down to adjust the number in the Preset Count column

to set the stroke count the machine should stop at.

Digit Lockout

Button

Press this button to keep the stroke count setting.

Reset Button

Push Button

Press this button to reset the current stroke count.

RESET BUTTON

CURRENT COUNT DISPLAY

PRESET COUNT DISPLAY

DIGIT LOCKOUT

DIGIT MODIFIERS

Figure 2. Stroke Counter

Содержание RTM-HVUPS Seires
































Результаты поиска

Содержание RTM-HVUPS Seires

Отзывы:

Бренды по названию

Популярные бренды

MVP RTM-HVUPS Seires, Руководство по эксплуатации

Результаты поиска

Содержание RTM-HVUPS Seires

Отзывы:

Бренды по названию

Популярные бренды