MUTOH VJ-628 ValueJet Скачать руководство пользователя страница 72

Страница: 72 / 80

72 Handling messages/error messages

Troubleshooting

VSM is used to check error/warning when problem happens and to check messages while the product is operating correctly.

The error LED in the operation panel becomes ON (flashes in warning state), and a buzzer sounds.

Handling messages/error messages

Checking message/error/warning

[1]

Launch VSM.

"Launching VSM" on page 9

[2]

Check [Status Info.].

• Message/error/warning contents are displayed.
• When countermeasures are displayed, follow them.

Note

• When the remote panel of VSM is launched, it can be also checked in [Printer Status] - [Status Info.].
• Operations may be temporarily paused when an error occurs. When an error is corrected, it restarts the operation.

Error display of operation panel

[1]

Short press the operation key on the operation panel, when the

buzzer continues sounding.

• The buzzer stops.

[2]

Check error/warning contents with VSM and handle the error/warning.

"Checking message/error/warning" on page 72

Troubleshooting

Press!

Содержание VJ-628 ValueJet

















































































Результаты поиска

Содержание VJ-628 ValueJet

Отзывы:

Бренды по названию

Популярные бренды

MUTOH VJ-628 ValueJet, Руководство по эксплуатации

Результаты поиска

Содержание VJ-628 ValueJet

Отзывы:

Бренды по названию

Популярные бренды