MUTOH VJ-626UF Скачать руководство пользователя

Страница: 8 / 144

8 Name of each part

Introduction

Name of each part

Printer’s main body

Introduction

Waste ink tube

Waste fluid is drained
from the tube. (This tube
is covered with the light
blocking cover.)

AC Inlet

Network connector

Connect an Ethernet cable.

Carriage

Contains the print head,
the LED pointer and
UV-LED unit.

UV-LED unit

Unit that emits the UV
(ultraviolet) light to cure
the ink.

Cartridge slots

Install an ink cartridge
or cleaning cartridge.

Table

The media is printed on this.
It has a vacuum fan inside.

LED pointer

Used for setting the media
placement set position and
the origin pointposition.

Obstacle sensor

Sensor for making sure
the media does not
contact the print head.

Front cover

Open when loading
media.

Handle

This handle is used for
service/maintenance by
maintenance personnel.
DO NOT use it for any purpose
other than instructed in this
manual.

Maintenance cover

Open when performing
maintenance.

Operation panel

Operation panel P.9

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды