VJ-1614 INSTALLATION MANUAL
VJ1614E-I-00
6
2
1
1
1
2
1
1
1
1
5mm 5mm
5mm
5mm
2
1
2
1
2
1
3
1
2
1 3
4
2
3
4
2
1
1
3
2
4
1
2 4
1
1
2
1
2
2
3
1
3
1
2
4
2
3
4
1 3
7. Raise the media loading lever.
"Lever Up" is displayed on the operation panel.
8. Open the front cover.
9. Insert the roll media into the media feed slot.
10. Pull the roll media approximately 1 m out of the
media feed slot, which is inside the front cover.
11. While holding the front end of the roll media,
wind the media back for a short distance by turn-
ing the flanges of the roll media holders so that the
media is not slack or slanted.
If you release your grip on the roll media while it
is being wound, the media may slip off the media
feed slot and fall behind the printer.
Make sure that the right end of the roll media
does not go beyond the media loading mark. It
may affect print quality.
When loading roll media, set each side of the me-
dia at least 5 mm away from the edges of the pressur-
izing roller. Failing to do so may cause the media to
slip or wrinkle while being printed on.
12. If the distance between the edge of the roll media and
the pressurizing roller is less than 5 mm, follow
the procedure below to adjust the position of the
roll media.
a. Loosen the fixing levers of the right and left roll
media holders, and move the roll media to the
right or left.
b. After moving the roll media, tighten the fixing
levers.
Be sure to press the roll media holders against the
printer while locking them.
13. Lower the media loading lever.
When applying pressure on the media, lower the
media loading lever further.
14. Close the front cover.
8 Loading the roll media
This section describes how to load roll media.
Place the roll media in the center of the printer.
Follow the steps below to load roll media.
1. Loosen the fixing levers of the right and left roll
media holders, and stretch the levers wider than
the width of the roll media.
2. Tighten the left roll media holder.
3. Attach the roll media to the left roll media holder.
4. Attach the right roll media holder to the roll media
and tighten the fixing lever.
5. Loosen the fixing levers of the right and left roll
media holders, slide the roll media to the center
and tighten the levers.
6. Turn the printer ON.
The printer starts initial operation.
"Media End" is displayed on the operation panel.
No.
Name
1
Media loading lever
No.
Name
1
Front cover
No.
Name
1
Media loading lever
No.
Name
1
Roll media holder (Left)
2 Roll media holder (Right)
No.
Name
3
Roll media
4
Fixing levers
No.
Name
1
Media loading lever
No.
Name
1
Front cover
No.
Name
1
Roll media
No.
Name
2
Media feed slot
No.
Name
1
Roll media
No.
Name
2
Media feed slot
No.
Name
1
Roll media
No.
Name
2
Pressurizing roller
No.
Name
1
Roll media
No.
Name
2
Media loading mark
No.
Name
1
Roll media holder (Left)
No.
Name
2
Fixing lever
No.
Name
1
Roll media holder (Left)
No.
Name
2
Roll media
No.
Name
1 Roll media holder (Right)
2
Roll media
No.
Name
3
Fixing lever
No.
Name
1
Roll media holder (Left)
2 Roll media holder (Right)
No.
Name
3
Roll media
4
Fixing levers
No.
Name
1
Roll media holder (Left)
2 Roll media holder (Right)
No.
Name
3
Roll media
4
Fixing levers
NOTE
NOTE
NOTE
NOTE
