MUTOH ValueJet VJ-1624WX Скачать руководство пользователя

Страница: 324 / 358

7 Troubleshooting

VJ-1624X/1624WX/1924WX OPERATION MANUAL

324

7.1 Malfunctions and failures

7.1

Malfunctions and failures

This section describes undisplayed malfunctions and failures of the printer, possible causes and
countermeasures.

7.1.1

Problems in installation and introduction

(1) Cannot perform the initial ink charge

(2) Ink does not come out after the initial ink charge

No.

Possible cause

Remedy

Reference

Is Front cover open or Media loading lever
raised?

Close Front cover, or lower Media loading
lever.

3.4 Loading

media

Is Maintenance cover open?

Close Maintenance cover.

6.2.4 Cleaning

Cleaning wiper

6.2.5 Cleaning

the circumference
of Print head

Are all 4 Ink cartridges fully inserted?

Fully insert all 4 Ink cartridges.

6.1.1

Replacing Ink
cartridges

No.

Possible cause

Remedy

Reference

Is Ink cartridge cold and frozen?

Leave Ink bag at room temperature for at least
three hours, and perform cleaning several
times.

6.2.3 Head

cleaning

Is the power turned OFF during the initial ink
charge?

Turn the power ON again and continue the
initial ink charge.

3.3 Filling ink

Occasionally, normal printing cannot be
performed after the initial ink charge.

Perform cleaning several times, and check it
every time.

6.2.3 Head

cleaning

Содержание ValueJet VJ-1624WX







































































































































































































































































































































































Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы:

Похожие инструкции для ValueJet VJ-1624WX

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1624WX, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы:

Похожие инструкции для ValueJet VJ-1624WX

Бренды по названию

Популярные бренды