MUTOH ValueJet VJ-1624WX Скачать руководство пользователя | Manualshive

Страница: 47 / 358

background image

VJ-1624X/1624WX/1924WX OPERATION MANUAL

Before using

3.3 Filling ink

47

3.3

Filling ink

This section describes the procedure to install Ink cartridges for the first time.

CAUTION

• Before operation, make sure to read the Safety Data Sheet (SDS).

• When handling Ink cartridges or Ink packs, pay attention so that ink does not come

into contact with your eyes or skin.
If ink gets into your eyes or sticks to your skin, immediately wash it off with water.
Failing to do so might cause irritation or light inflammation of eyes.
In case of any abnormality, consult a physician immediately.

• Do not disassemble Ink cartridges or Ink packs.

If disassembled, ink might come into contact with your eyes or skin.

• Comply strictly with the following during ink filling.

• Do not turn OFF the printer.

• Do not unplug the power cord set.

• Do not open Front cover.

• Do not open Maintenance cover.

• Do not raise Media loading lever.

«
...
45
46
47
48
49
...
»

Содержание ValueJet VJ-1624WX







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ValueJet VJ-1624WX

Color imageRUNNER LBP5970

Бренд: Canon Страницы: 67

Color imageCLASS MF8280Cw

Бренд: Canon Страницы: 36

imagePROGRAF iPF8300

Бренд: Canon Страницы: 16

Бренд: DASCO Страницы: 2

DocuPrint 4050 NPS

Бренд: Xerox Страницы: 248

Бренд: Olivetti Страницы: 149

Бренд: NBS Technologies Страницы: 64

Бренд: Lexmark Страницы: 2

Бренд: 3D Systems Страницы: 83

Бренд: Epson Страницы: 150

FX-980 - Impact Printer

Бренд: Epson Страницы: 27

Бренд: Blocks Страницы: 68

Бренд: NCR Страницы: 17

Бренд: Riso Страницы: 5

Aficio MP W3600

Бренд: Aficio Страницы: 12

RING400PE SERIES

Бренд: Autonics Страницы: 34

Бренд: YIDIMU Страницы: 46

Бренд: Perfect-Office Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды