Mustang TOP 21 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

Mustang TOP 21 Скачать руководство пользователя страница 6

6

II. Installation

1. Unit installation position

To avoid poor ventilation, the unit air discharge should not be blocked when installation.
Please keep enough space around the unit for future maintenance. Right and wrong
installations are as below:

Wrong

Right

1. To get enough air for ventilation of the unit, the installation position should be with good

ventilation.

2. Ensure the installation position can hold the unit without noise and shake.

3. Ensure no direct sunlight to the unit. Set an awning if necessary.

4. Ensure rain and defrosting water can be discharged in the installation position.

5. Ensure the unit will not be covered by snow in the installation position.

6. Ensure the discharged air will not face strong air in the installation position.

7. Ensure the noise caused by the unit ventilation and operation will not affect the

neighbor.

8. Ensure the installation position will not be affected by garbage, oil and mist.

9. The unit will be damaged under the condition with oil(engine oil), salt(sea area)

and sulfide air(near thermal spring and refining factory).

N o tice :

«
...
4
5
6
7
8
...
»

Содержание TOP 21

































Отзывы:

Нет отзывов