Murray EV3850x4B Скачать руководство пользователя

Страница: 18 / 24

TROUBLE SHOOTING CHART

F–041104L

TROUBLE

CAUSE

CORRECTION

Engine difficult to start

Stale fuel

Drain fuel tank. Fill with fresh

fuel.

Clogged fuel filter

Replace fuel filter

Engine runs erratically

Dirt in fuel tank or out of fuel

Clean fuel tank.

Engine runs erratically

Carburetor out of adjustment

See Carburetor Adjustment

section.

Engine will not run at full

Fouled spark plug

Clean and set spark plug

gap.

Engine will not run at full
speed

Dirty air filter

Replace air filter.

Engine smokes

excessively

Plugged air filter

Replace air filter.

Debris interfering with blade

Clean debris from blade.

Cutting blade will not

rotate

Loose blade

Tighten blade nut.

rotate

Defective V–belt

Replace V–belt.

Blade will not cut properly

Defective quill bearings

Replace the quill assembly.

Blade will not cut properly

Damage or worn blade

Reverse the blade or replace

the blade.

Excessive vibration

Loose parts

Stop engine immediately.

Tighten all fasteners. If

vibration continues, take the

unit to an Authorized Service

Center.

Содержание EV3850x4B

























Результаты поиска

Содержание EV3850x4B

Отзывы:

Похожие инструкции для EV3850x4B

Бренды по названию

Популярные бренды

Murray EV3850x4B, Руководство по эксплуатации

Результаты поиска

Содержание EV3850x4B

Отзывы:

Похожие инструкции для EV3850x4B

Бренды по названию

Популярные бренды