manualshive.com logo in svg

Murray 387002x92A, Инструкция, Страница: 22 / 52

Поделиться
Скачать
Murray 387002x92A Скачать руководство пользователя страница 22

MAINTENANCE

22

F-040717L

HOW TO ADJUST THE BLADE ROTATION CONTROL

WARNING: To prevent an injury, the blade rotation

control must operate correctly.

1. Stop the engine. Disconnect the wire from the spark plug.
2. Before you adjust the 

blade rotation control

, check and level

the mower housing. See “How To Level The Mower Housing.”

Make sure the mower housing is level before go to the next

step.

3. Set the height of the mower housing in the lowest position.
4. Move the 

blade rotation control

 to the 

ENGAGE position

(Figure 14). Check the 

plastic indicator

 inside the 

blade drive

spring

 (Figure 15). The end of the 

plastic indicator

 must be

aligned ( + or  -  1/8 inch / 3 mm) with the last coil of the 

blade

drive spring

.

5. If the 

plastic indicator

 is more than 1/8 inch (3 mm) from the

last spring coil, an adjustment is needed. Move the 

blade rota-

tion control

 to the 

DISENGAGE position

. Disconnect the

blade control rod

 from the 

pivot bracket

. Turn the 

adjustable

nut

 clockwise to increase the length of the coils. Turn the 

ad-

justable nut

 counterclockwise to decrease the length of the

coils.

6. Connect the 

blade control rod

 to the 

pivot bracket

. Move the

blade rotation control

 to the 

ENGAGE position

. Check the

adjustment of the 

blade drive spring

.

7. Move the 

blade rotation control

 to the 

DISENGAGE posi-

tion.

 Check the operation of the blade brake. Rotate the pulley

with your hand. Make sure the pads for the blade brake are

pressed tightly against the pulleys.

IMPORTANT: If the brake pads do not press tightly against

the pulleys, replace the mower drive belt and repeat steps

1-7.  Then, complete the remaining steps. Correct

replacement parts and assistance are available from an

authorized service center.

8. Move the 

blade rotation control

 to the 

ENGAGE position.

Check the pads for the blade brake. If the pads are excessively

ÏÏ

ÏÏ

ÏÏ

Blade Rotation Control

Engage Position

Disengage

Position

Throttle

Control

Figure 14

worn or damaged, replace the 

brake pad

 assemblies. Correct

replacement parts and assistance are available from an autho-

rized service center.

9. Attach the wire to the spark plug. Mow for a short distance and

again check the operation of the 

blade rotation control

.

10. When you move the 

blade rotation control 

to the

DISENGAGE position

, all movement will stop within five sec-

onds if the adjustment is correct. If there is movement of the belt

or the blades continue to rotate, engage and disengage the

blade rotation control

 five times to remove any excess rubber

from a new 

mower drive belt

. If there is still blade rotation from

the 

DISENGAGED position

, adjust the 

blade drive spring

until more of the 

plastic indicator

 extends beyond the end of

the last coil. This adjustment will decrease the spring tension.

If you need assistance, take the unit to an authorized service

center.

11. After you operate with a new 

mower drive belt

 for several

hours, check the tension of the 

blade drive spring

.

12. If you replace the 

mower drive belt

, adjust the 

blade rotation

control

.    

Figure 15

Pivot Bracket

Adjustable

Nut

Blade Control Rod

Brake Pad Against Pulley

Mower Drive Belt

Blade Drive Spring

Plastic Indicator

-1/8”

(3mm)

+1/8”

(3mm)

Blade Brake

(Brake Pad Against Pulley)

Содержание 387002x92A





















































Отзывы:

Нет отзывов